Operation; Alerts And Troubleshooting - Milwaukee M12 FUEL ONEFTR12 Operator's Manual

OPERATION

Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
Turning ON/OFF
Hold tool motionless when turning the tool ON.
Movement during the initial two second sensor
check may affect torque value. Press the power
button to turn the LCD ON. Press and hold the
power button to turn the LCD OFF. The tool will
go into standby mode within 2 minutes of nonuse
and sleep mode after 10 minutes. NOTE: In
standby mode, pressing the paddle switch or
power button will turn the tool back on. In sleep
mode, pressing the power button will turn the tool
back on.
Progress Light Bar
The progress light bar will display the progress to
achieving the target torque.
White: First light indicates 40% of the target torque
reached. Second light indicates 60% of the target
achieved. Third light indicates 80% of the target
achieved.
Green: Indicates targeted torque has been achieved.
Red: Indicates exceeded target torque.
White:
40%
White:
60%
White:
80%
Green:
Red:
Forward/Reverse Toggle
For forward (clockwise) rotation,
rotate the forward/reverse toggle
counterclockwise. Check the direc-
tion of rotation before use.
For reverse (counterclockwise)
rotation, rotate the forward/reverse
toggle clockwise. Check the direction
of rotation before use.
Lock Switch
To lock the paddle switch, slide the lock switch to
position. To unlock the paddle switch,
the locked
slide the lock switch to the unlocked
paddle switch will not work when the lock switch is
in the locked position.
Always lock the paddle switch or remove the battery
pack before performing maintenance, changing ac-
cessories, storing the tool and any time the tool is
not in use.
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from
0 to full RPM.
1. To start the tool, pull the paddle switch. NOTE: A
LED is turned on when the switch is pulled.
The tool will shut off automatically when maximum
run down torque is reached.
2. To vary the driving speed, increase or decrease
pressure on the switch. The further the switch is
pulled, the greater the speed.
3. To stop the tool, release the paddle switch.
Selecting Torque
1. Set the target torque.
2. Select the units of measure.
3. Apply torque. Grasp the centre of the handle
and apply torque to the fastener until the progress
lights display green. The tool will automatically
stop prior to target torque to prevent over torquing.
4. Finish by hand to reach target torque.
5. Press
the tool.
6. Release torque. The torque reading on the LCD will
display for > than 5 seconds or the next trigger pull.
Adjusting target torque
Target torque is the required torque value for the
fastener being installed. Adjust the target torque to
meet the desired torque specifications
Adjusting torque range
Torque range indicates the acceptable range of val-
ues for a successful install. Adjust the torque range
to meet the recommended torque specifications
Adjusting rundown torque
Rundown torque is the approximate torque value the
motor will stop driving the tool. The tool will tighten
the fastener to the selected preset percentage and
then stop. Finish by hand to reach target torque.
NOTE: Rundown torque changes the tools output
power. Adjust the rundown torque to help prevent
over torquing of the fastener.

ALERTS AND TROUBLESHOOTING

Memory for Saved Events
Forward
The tool has a limited amount of memory dedicated
to saved events. When keeping a prolonged list
of events outside of the tools memory, refer to the
ONE-KEY
saved events, connect to the ONE-KEY
Reverse and clear the memory on the tool using the app.
This ensures that the events are backed up online
within the ONE-KEY
will prompt that the memory is close to being full or
reached capacity.
position. The
5
APPLICATIONS
Basic Functions
to save an event, to stay consistent with
Advanced Functions
Display Alerts
™
app for better backup. To clear your
™
cloud. NOTE: The display
™
app