Related Manuals for Hafele SAFE-O-TRONIC LS 100
Summary of Contents for Hafele SAFE-O-TRONIC LS 100
- Page 1 Mounting Instructions Item No.: 231.98.000/001/002/003 ® SAFE-O-TRONIC access Electronic Identification and Locking System Manual LS 100 ® SAFE-O-TRONIC LS Cabinet Lock Dimensions in mm Inches are approximate...
-
Page 2: Notes On This Manual
Notes on this manual ® Copyright 2010 by Schulte-Schlagbaum AG Nevigeser Straße 100-110 D-42553 Velbert Phone: +49 2051 2086-0 http:/www.sag-schlagbaum.com Document number: 6-703-2 34R1.0 • This manual replaces all previous versions. • The details in this manual are subject to change without prior notification. •... -
Page 3: Table Of Contents
Table of Contents Notes on this manual..................2 Safety and warning notes................2 Table of contents.................... 3 Control elements.................... 4 Lock with mounting components..............5 Installation information................. 6 ..................6 Preparation of the door ......................6 Installation ............... 6 Replacement of the rotary knob (as needed) .............. -
Page 4: Control Elements
Control Elements LED display red / green Exchangeable plate Rotary knob Capacity keypad OK key: Finish of Code entry √ Abort key: Code entries or programming operations can be rejected by pressing the abort key Keys 1, 2, 3, 4, 5, 6, 7, 8, 9, 0: Number keys for Code entry... -
Page 5: Lock With Mounting Components
Lock with Mounting Components 1 Lock 2 Nut for mounting the lock on the door 3 Grommet for setting the rotational direction of the rotary knob in order to lock 4 Locking cam (A cropped or hook-shaped locking lever can also be used depending on the properties and condition of the cabinet.) 5 Fastening bolt for locking lever 6 Bushing for fastening the lock to the door for door thickness from 10 mm to 18 mm... -
Page 6: Installation Information
Installation Information Preparation of the door The following holes must exist in the door corresponding to the drawing: 1. Punched hole, dimensions 19.1 mm / 16 mm. A round hole with a diameter of 19.1 mm can also be drilled at this position. 2. -
Page 7: Setting The Rotational Direction For Locking
Installation Information Settng the rotational direction for locking The setting of the rotational direction described here is for a lock with a rotary knob that is turned to the left for locking. 1 Lock marked with left handed rotational direction for locking 2 Grommet that is attached to the lock on the inside of the door. -
Page 8: Replacing The Plate (E.g. For Numbers, Logo, Etc.)
Installation Information Replacing the plate (e.g. for numbers, logo, etc.) After inserting a small screwdriver into the center of the plate, the old plate is levered out of the lock. A new plate can then be snapped in. Notice: The old plate is destroyed when the plate is replaced. -
Page 9: General Information
General Information Capacitive keypad The SAFE-O-TRONIC® LS 100 uses a capacitive keypad. Notice: The capacitive keypad cannot be operated if you are wearing gloves. UserCode The UserCode serves locking or opening of the cabinet or locker by the user. Any four-digit code can be programmed as the UserCode. -
Page 10: Operation
General Information Operation Operation is supported by the red/green LED display and an acoustic acknowledgement by means of signal transmitters. key can be used to abort an input procedure. The procedure is aborted automatically if there is a stop of more than three seconds between operating the individual keys. -
Page 11: Initial Operation
Initial Operation For initial operation every SAFE-O-TRONIC® LS 100 lock has to be programmed using MasterCode2. Please note: Please make sure that unauthorized persons do not gain knowledge of the programmed MasterCode2. Programming MasterCode2 Press the OK and abort keys simultaneously √... -
Page 12: Locking And Opening Using Mastercode2
Initial Operation Locking and opening using MasterCode2 The operator of the facility can use MasterCode2 at any time to open or lock the locker fitted with the SAFE- O-TRONIC® LS 100. Entering MasterCode2 Notice: 3, 5, 1, 9, 7 is only an example code! √... -
Page 13: Further Functions
Further Functions Altering MasterCode2 Press the OK and abort keys simultaneously √ Enter active MasterCode2 Notice: 3, 5, 1, 9, 7 is only an example code! Press the OK key √ Press 2 (“2” for MasterCode2) ... -
Page 14: Programming Mastercode1
Further Functions Programming MasterCode1 MasterCode1 is not activated in the factory and must be programmed by the operator. Notice: An identical code for MasterCode1 and MasterCode2 is not permitted. Press the OK and abort keys simultaneously √ Enter active MasterCode2 Notice: 3, 5, 1, 9, 7 is only an example code! ... -
Page 15: Opening Using Mastercode1
Further Functions Opening using MasterCode1 After programming, a locker can be opened with the help of MasterCode1. Enter MasterCode1 √ Then press the OK key Release using MasterCode2 If a compartment that is fitted with a SAFE-O-TRONIC® LS 100 is opened using MasterCode1, it stays blocked for the entry of a UserCode. -
Page 16: Further Information
Further Information LED Display All important actions and operating conditions are indicated by the LED display and are intended to contribute to finding the causes of failures and operating errors. The following table lists the meaning of the individual signals. Status messages: green green... -
Page 17: Troubleshooting / Operating Errors
Troubleshooting / Operating Errors You are able to see errors and operating errors in the status messages of the LED display and then correct them accordingly. Reset should be carried out in the case that other non-defined conditions arise and the lock does not operate flawlessly even though the battery has been replaced. -
Page 18: Technical Data
Technical Data Indicators: 2 x LED green 2 x LED red Acoustic signal: Signal transmitter Battery: Battery pack: 3 x alkaline cells (AAA) Battery life cycle: Approx. 3 years at 30 lockings per day Temperature ranges Function: -10˚C to +65˚C (14˚F to 149˚F) Storage: -25˚C to +65˚C (-13˚F to 149˚F) Relative humidity:... -
Page 19: Drilling Template
Further Functions Technical Data Notice: Depending on the printer there can be dimensional deviations when printing this drilling template. Therefore, please re-measure the drilling template before use! 3901 Cheyenne Drive P.O. Box 4000 Archdale, NC 27263 1-800-423-3531 www.hafele.com...
Need help?
Do you have a question about the SAFE-O-TRONIC LS 100 and is the answer not in the manual?
Questions and answers