Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Rosewill 6A Series
Summary of Contents for Rosewill 6A Series
- Page 1 CASE 6A Series USER Manual www.rosewill.com...
-
Page 2: Table Of Contents
Installation 1.Opening Chassis 2.Installing Motherboard 3. Installing Power Supply 4.Installing 5.25" Device 5.Installing 3.5" Floppy 6.Installing 3.5" HDD 7.Installing Add on Card P.0 8.USB port P. 9.Audio Port P.2 Information P.3 © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 3: Configuration
Air Filter One air filter in the front panel I/O Port Bracket Supports one I/O port bracket for standard ATX M/B Megal Material 0.8 mm thickness SECC rustproof & galvanized JIS Steel © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 4: Features Descriptions
Sliding Rails for 5.25" Vertical sliding HDD cage Device HDD cage with Shockproof Add on Card Kit No Screw Neded to Secure Front IO Ports Rubber Pads & Open the Left Side Panel © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 5: Installation
Roll the side cover anticlockwise Press the 2 buttons on both sides the back plane to open of lower front panel and carefully pull down and forward to move the front panel © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 6: Installing Motherboard
Locate and align the screw holes on the Secure the motherboard on the studs with motherboard and chasis; place the the screws #6-32 motherboard at the correct position, and then screw brass studs onto chasis's metal shell © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 7: Installing Power Supply
CASE 6A series User Manual 3.Installing Power Supply Put your power supply in the right position and fasten screws from back panel of the case © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 8: Installing 5.25" Device
5.25" device for easier installation CD-ROM and screw the rails • When you feel difficult to pull out your railed 5.25" device, push it onto the 5.25" device down a little will help you © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 9: Installing 3.5" Floppy
Fasten the floppy on cage by Slide the small cage into drive wards to take off the small cage HDD into the drive bay screws bay, make sure the cate is properly positioned © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 10: Installing 3.5" Hdd
Slide the large cage into drive large cage the large cage out cage bay and fasten the thumb screws *Handle with care because HDD is likely to be damaged by careless management © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 11: Installing Add On Card
Loosen the kit above the slot you want to install your add on card in and Insert your add on card into the Push down the kit to fasten the remove the metal cover by your flat screwdriver. right slot add on card © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 12: Usb Port P
Any installation mistake may cause severe damage to your motherboard and other components. 3. The USB 2.0 connector design is to prevent installation error. Please connect the USB 2.0 port & M/B USB pin. See the figures as belos. © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 13: Audio Port
M/B. 4. The Audio connector design is to prevent installation error. Please connect the audio port & M/B audio pin. See the figures as below. © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... - Page 14 Please register your product at : www.rosewill.com/ for complete warranty information and future support for your product. If you have any question while using our products, please feel free to contact us at feedback@rosewill.com Support Phone Number: 800-575-9885 Support Email: techsupport@rosewill.com...
Need help?
Do you have a question about the 6A Series and is the answer not in the manual?
Questions and answers