Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Rosewill CASE 6A Series
Summary of Contents for Rosewill CASE 6A Series
-
Page 2: Table Of Contents
5.Installing 3.5" Floppy 6.Installing 3.5" HDD 7.Installing Add on Card P.10 8.Clearing Air Filter P.11 9.USB port P.12 10.Audio Port P.13 11.Front Panel LED P.14 12.System Control Connectors P.15 Information P.16 © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 3: Configuration
One air fi lter in the front panel I/O Port Bracket Supports one I/O port bracket for standard ATX M/B Megal Material 0.8 mm thickness SECC rustproof & galvanized JIS Steel © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 4: Features Descriptions
Sliding Rails for 5.25" Vertical sliding HDD cage Device HDD cage with Shockproof Add on Card Kit No Screw Neded to Secure Front IO Ports Rubber Pads & Open the Left Side Panel © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 6: Installing Motherboard
Locate and align the screw holes on the Secure the motherboard on the studs with motherboard and chasis; place the the screws #6-32 motherboard at the correct position, and then screw brass studs onto chasis's metal shell © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 7: Installing Power Supply
CASE 6A series User Manual 3.Installing Power Supply Put your power supply in the right position and fasten screws from back panel of the case © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 8: Installing 5.25" Device
5.25" device for easier installation CD-ROM and screw the rails • When you feel diffi cult to pull out your railed 5.25" device, push it onto the 5.25" device down a little will help you © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 9: Installing 3.5" Floppy
Fasten the fl oppy on cage by Slide the small cage into drive wards to take off the small cage HDD into the drive bay screws bay, make sure the cate is properly positioned © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 10: Installing 3.5" Hdd
Slide the large cage into drive large cage the large cage out cage bay and fasten the thumb screws *Handle with care because HDD is likely to be damaged by careless management © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 11: Installing Add On Card
Loosen the kit above the slot you want to install your add on card in and Insert your add on card into the Push down the kit to fasten the remove the metal cover by your fl at screwdriver. right slot add on card © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 12: Clearing Air Filter
Push the hooks marked in red circles. Detach the air filter to clean. NOTE : Some 6A models have the air filter in the front panel. Don’t have to work previous steps. ( ex.R6AU6, R6AR6 ) © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 13: Usb Port
9.1 Read your motherboard’s user manual to find the pins for the USB connector. 9.2 Find the USB connector and connect it to the pins. M/B USB PINS USB+5V USB+5V USB_P5 - USB_P8 - USB_P5 + USB_P8 + © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 14: Audio Port
10.1 Read your motherboard’s user manual to find the pins for the Audio connector. 10.2 Find the Audio connector and connect it to the pins. M/B Audio PINS MIC2 AGND MICPWR +5VA Line out_R Bline_out_R Line out_L Bline_out_L © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... -
Page 16: System Control Connectors
NOT every motherboard has the same layout of these system control pins. Please refer to your motherboard user’s manual to check the layout Reset Switch before the installation. IDE_LED RESET System Power LED HDD Activity LED © 2004-2006 Rosewill Inc. All rights reserved by Rosewill... - Page 18 www.rosewill.com...
Need help?
Do you have a question about the CASE 6A Series and is the answer not in the manual?
Questions and answers