Table of Contents
Advertisement
installation
e) Cut the 2 ft. or 4 ft. section of rigid pipe to
length. Ensure that the pipe length when
cut will seat onto both the starter collar
and the 90
elbow. Crimped section of
o
rigid pipe seats into the 90
Only cut the uncrimped side of pipe.
Dismantle all pipe sections including vent
terminal.
3. Attach the 4" dia. flex liner to the vent terminal
ensuring that the flex overlaps the collar of the
vent terminal by a minimum of 1-3/8"(35mm).
Use Mill-Pac to seal and secure with 3 of the
#8 x 1/2" screws (stainless steel).
4. Attach the adjustable pipe section to the vent
terminal using Mill-Pac and attach with 3 of
the #8 x 1/2" screws (stainless steel).
Note: The pipe seam should be facing
down.
Note: To make the installation more
a e s t h e t i c a l l y p l e a s i n g , w e
recommend framing out a square
that the cap can be mounted on.
Note: If installing termination on a
siding covered wall, a vinyl siding
standoff or furring strips must be
used to ensure that the termination
is not recessed into the siding. For
vinyl siding standoff installation
refer to the Dura-
Vent Termination
instructions.
5. Slide the partially connected
pipe and vent terminal
assembly through the wall
thimbles (from the exterior
into the interior) and secure the cap to the
exterior wall with 4 of the supplied screws (#8
x 1-1/2" drill point, stainless steel). Note: pilot
holes will need to be drilled through the wall
thimble on all 4 corners.
Note: The four screws provided for the
vent cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6. A bead of non-hardening mastic should be run
around both the termination and vinyl siding
standoff to prevent water from entering and
to make a tight seal between the cap and the
standoff.
7. Stretch the 4" dia. flex liner out fully and get a
trial fit of the liner onto the 4" dia. starter collar.
28
|
Regency
U39EX ULTIMATE™ Freestanding Gas Stove
®
elbow.
o
8. Cut the 4" dia. flex liner to the desired size.
Hint: leave an extra 12" to 16" of length, this
will make the final assembly easier to work with.
9. Secure the 4" dia. flex liner to the 4" adapter
with Mill-Pac and 3 of the #8 x 1/2" screws
(stainless steel).
10. Slide the decorative Thimble Cover over the
pipe sections and secure with 4 screws (#8 x
1-1/2" drill point, black) to the wall.
a l l
i d e W
Furstrp.eps
11. Slide the 90
O u t s
ft. or 4 ft. pipe section (crimp end up) over the
see also c34020a.eps
4" dia. flex liner.
Furring
12. Slide the trim collar over the adjustable pipe
Strips
sections to cover the joint of the telescopic
section.
13. Install the spring spacers onto the pipe sections.
14. Secure the 4" dia. flex liner with adapter onto
the stove collar. Put a bead of Mill-Pac around
r i e u r
the appliance adapter and secure with 3 screws
e x t é
M u r
furstrpf.eps
(#8 x 1/2, stainless steel).
french
15. Attach the pipe section onto the starter collar
by sealing with Mill-Pac and securing with 3 of
Fourrures en bois
the #8 x 1/2" (black) screws. Pipe seams should
be facing the wall.
16. Attach the 90
sealing with Mill-Pac and securing with 3 of the
#8 x 1/2" screws (black).
17. Slide the adjustable pipe section onto the 90
elbow. The flex may have to be compressed back
in order for the adjustable pipe to properly mate
elbow (crimp end up) and the 2
o
elbow onto the pipe section by
o
to the elbow. Seal with Mill-Pac and secure
with 3 of the #8 x 1/2" screws (black). Pipe
seams facing down.
18. Install the trim collar over the starter collar
and secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE:
For best results and optimum
performance with each approved venting
system, it is highly recommended to apply
"Mill-Pac" sealant (supplied) to every in-
ner pipe connection. Failure to do so may
result in drafting or performance issues
not covered under warranty.
o
Advertisement
Table of Contents
