Ryobi RA-N-B Operator's Manual
  1. Manuals
  2. Brands
  3. Ryobi Manuals
  4. Power Tool
  5. RA-N-B
  6. Operator's manual

Ryobi RA-N-B Operator's Manual

Air nibbler
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RA-N-B
AIR NIBBLER
OpERAtOR's MANUAL
ORIgINAL INstRUctIONs

Advertisement

Table of Contents
loading

Related Manuals for Ryobi RA-N-B

Summary of Contents for Ryobi RA-N-B

  • Page 1 RA-N-B AIR NIBBLER OpERAtOR's MANUAL ORIgINAL INstRUctIONs...
  • Page 2 Important! It is essential that you read the instructions in this manual before operating this machine. Subject to technical modifications.
  • Page 3 DEscRIptION 1. Cutting set 5. NITTO style coupler 8. Cutter 11. Locking nut 2. Cutting slot 6. Quick connector (not 9. Cutter retaining 12. Nibbler head 3. Trigger included) screw 4. Air inlet 7. Air hose (not included) 10. Connecting rod Fig.1 Fig.2 Fig.3...
  • Page 4 Fig.7 Fig.8 35mm 15 mm 22 mm Fig.9 Fig.10 Quick Quick connector connector Lubricator Filter Tool compressor Cut-off valve Quick Quick coupler coupler Regulator Air hose Fig.11 (0-8.5 bar)

  • Page 5: General Safety Rules

    interruption of the energy supply. gENERAL sAfEty RULEs ■ Use only lubricants recommended by the manufacturer. ■ For multiple hazards, read and understand the safety ■ Avoid direct contact with the inserted tool during and instructions before installing, operating, repairing, after use as it can become hot.

  • Page 6: Noise Hazards

    ■ The nibbler or shear is not intended for use in vIBRAtION hAzARDs potentially explosive atmospheres and is not insulated The information for use shall draw attention to vibration against contact with electric power. hazards that have not been eliminated by design and ■...

  • Page 7: Intended Use

    Air Nibbler for repair. 2. Injuries and damage to property due to broken cutting Model number RA-N-B attachments or the sudden impact of hidden objects Average air consumption 335 L/min @ during use.

  • Page 8: Maintenance

    ■ Route the air hose along a safe route to reach the cAUtION work area. The air hose must be long enough to reach the work area with enough extra length to allow free Do not allow the product to free run for an extended movement while working.

  • Page 9: Replacing The Blade

    ■ Only lubricants recommended by the manufacturer should be used. Wear ear protection. ■ Drain the air tank daily. Water in the air line will damage the product. ■ If the product cannot be used anymore, make sure to Lubricate with air tool oil daily. dispose of it so as not to impose hazards on people and the environment.
  • Page 10 pARts LIst Description Description Description Description Cutting Set Bearing 6200-2Z Straight Pin 1.5*6 32.2 Strainer Hexagon Nut Washer Cylinder O-ring 3.2*1.9y Screw Snap Ring Rotor Cutter Pole Hexagon Nut Blade Spring Connecting Rod Planet Cageincl Back Cylinder Head O-ring 8*2 L-Head Bearing 626-2Z Shaft Bushing...

  • Page 11: Troubleshooting

    tROUBLEshOOtINg WARNINg If any of the following symptoms appears during operation, stop using the product immediately, or serious personal injury could result. Only qualified persons or an authorised service centre can perform repairs or replacement of the product. pROBLEM cAUsE sOLUtION Product will not run.
  • Page 12 techtronic Industries Australia pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149, Melbourne, Australia techtronic Industries N.z. Limited 2 Landing Drive, Mangere Auckland, 2022, New Zealand...

Table of Contents