Safety instructions Dear user Please note! Congratulations on your purchase of a Faber fire! A quality product from which you will experience It is advisable to always install a screen for the fire- warmth and atmosphere for many years. We rec-...
For appliances with flexible gas pipes, the C31, outlet via roof control unit (fig. 1.3) is mounted at the For a (flat) roof, use a Faber roof outlet with a di- bottom of the crate. Detach and mount it ameter of 100/150mm.
Page 13
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H We advise using a gas connection directly from the HPL module (Hybrid Pro Light) gas meter to the appliance, with a shut-off valve in Place the power supply (see fig. 1.7) of the the proximity of the appliance, which must always HPL/step module in a cool place and near to the be freely accessible.
Page 14
Use For the height of the plateau, observe the (optional) Faber ventilation grids (article num- point N (fig. 2.7 and 2.8). ber A9296400) or a similar alternative with a mini- ...
Page 15
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H Keep the included decoration instruction card Disassemble the front glass (fig. 3.3). close. For replacing the glass repeat the steps in reverse Chapter 17 provides an overview of the complete order.
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H Placing log set Measuring the inlet pressure: Close the shutoff valve. Turn the measur- Place wood log 2 over the center burner. ing nipple “E” (fig. 1.3) a few turns to Make sure the ignition and ionization pin open and connect a measuring hose to are not obstructed by the wood log.
If the ratio is greater than 1:100 or Remove the front glass (see chapter 5). flue gases are measured in the air supply, check You can clean the glass with Faber glass polish. the points in section 7.1. This is a specially formulated cleaning agent that can be ordered at authorized Faber dealers.
Page 18
A simple way to calculate whether the exhaust ments H, J, L, M, P and R configuration is possible in combination with your (fig. 12.1 and 12.2). fireplace, use the “Faber Flue App V2”: Elbows 90° in the horizontal plane: Horizontal elbows are elbows entirely in the horizontal plane (fig.
Page 19
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 11.1 Restrictor table (100/150) MatriX 1050/500 I,II,III H and MatriX 1050/650 I,II,III H Start length (STL) Vertical (TVH) and Horizontal (THL) 30,2 30,2 40,2 40,2 40,2 50,2 50,2 50,2 60,2 60,2 60,2...
Page 20
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 11.2 Restrictor table (130/200) MatriX 1050/500 I,II,III H and MatriX 1050/650 I,II,III H Start length (STL) Vertical (TVH) and Horizontal (THL) 20 < < < <...
Page 21
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 12 Examples flue material 21 < < < <...
Page 22
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 13 Calculation sheet Start length (STL) First part on top of the appliance Value Flue length from 0,1m till 0,45m Flue length from 0,5m till 0,90m Flue length from 1m till 1,4m Flue length from 1,5m till 2m Flue length 2m or more Bend 90°...
Page 23
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H Found value Search in the table at TVH and THL and enter the value that is found. ……………………………… If the detected value is a number, check whether the completed STL is higher or equal to the value in the table.
Page 24
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H Technical data 14.1 MatriX 1050/500 I,II,III H Technical data Type indication(s) MatriX 1050/500 I,II,III H Type appliance C11/C31/C91 Diameter outlet/inlet 130/200 Gas connection 3/8" Indirect heating functionality Category II2H3P Symbol Unit Reference gas/inlet pressure...
Page 25
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 14.2 MatriX 1050/650 I,II,III H Technical data Type indication(s) MatriX 1050/650 I,II,III H Type appliance C11/C31/C91 Diameter outlet/inlet 130/200 Gas connection 3/8" Indirect heating functionality Category II2H3P Symbol Unit Reference gas/inlet pressure G20-20 G31-37...
Page 26
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 15 Outlet position Please note! These rules apply only for the proper functioning of the unit, for ventilation and environmental protec- tion you need to comply with the applicable rules as defined in the building regulations. Short roof terminal.
Page 27
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 16 Top view sectional burner MatriX 1050 I,II,III H 16.1 Position led spots and burners 16.2 Position light guides 27 < < < <...
Page 28
Installation manual MatriX 1050/500 I,II,III H & MatriX 1050/650 I,II,III H 17 Log set lay out MatriX 1050 I,II,III H Use the included decoration instruction card, or for a clear instruction video, scan the QR code 28 < < < <...
Need help?
Do you have a question about the MatriX 1050/500 I H and is the answer not in the manual?
Questions and answers