Adding A Further Garden/Lawn Area (See Figure I); Mowing - Honda Miimo HRM40 Live Owner's Manual

Adding a further Garden/Lawn
Area (see figure I)
To install the Miimo to an additional lawn area, please
follow the instructions in the Installation Guide .
Separate lawn area with separate docking station (see
figure I, right): The mower can be used on up to three
different lawns . For an additional lawn area, a separate
docking station (see figure A) and the necessary perimeter
wire and pegs are required . If a schedule or the Honda
"Smart Timer" calendar function is selected, it will cut
the grass of the area it is in, within the time slots .
Switch off the mower when transporting it between the
individual lawn areas .
Note: software updates have to be carried out on the
mower in every docking station .
To ensure remembering which docking station belongs
to which garden, it is recommended to label the docking
stations with the garden number and description when
storing them for winter .
Without separate docking station: It is possible to
connect the lawn areas by placing the perimeter wire
between the two lawn areas parallel to each other as
close as possible (see figure I, top left). The additional
lawn area without docking station is not recorded
in the map memory and the mower will not use the
Map & Mow cutting strategy in this lawn area without
the docking station . The maximum recommended lawn
area without a docking station is 40 m
will mow until it runs out of battery and will need to be
carried back to the docking station for charging .

Mowing

f Do not let children ride the mower.
f Press the stop button on top of the mower before
lifting. Always lift the mower by its handle. (see
figure F)
Make sure the cutting area is free of small animals such
as hedgehogs or tortoises .
After successful installation, you can begin mowing
immediately by pressing "mow" on the free Honda
Mii-monitor App . You could also set up a programmed
schedule, using the Honda "Smart Timer" functionality,
which can also plan future cutting sessions based on
when it is forecasted to rain .
A manual "calendar" can also be set up according to your
specific needs.
The mower must mow a lawn area 3 times completely
(do 3 full cuts) to learn the lawn area. During the
learning phase, the visual result may not be optimal .
Approximate runtimes for complete garden coverage
using Map & Mow are listed below . Please note that the
runtimes will vary depending on the lawn complexity
and number of objects within the garden .
100 m
350 m
400 m
Set a schedule with frequent repetitions . This achieves
good mowing results, the battery charge lasts longer and
you avoid clippings on the lawn .
When the mower is mowing
In "manual" mode, the mower works until the lawn
is mowed . Mowing is interrupted only for charging
the battery . When the lawn area is mowed, the mower
returns to the docking station .
In the programmable "Calendar" mode or with the
Honda "Smart Timer" calendar function, the mower
operates continuously for a set period of time . Mowing
is interrupted only for charging the battery . If the lawn
area is mowed before the time period expires, the mower
returns to the dock .
To stop mowing prematurely, press the Dock button
in the Honda Mii-monitor App . You could also send
the mower back to the docking station by pressing the
confirm button H* on Miimo to confirm.
Energy saving mode
The mower reduces its energy consumption by
automatically switching off the power in the perimeter
wire when it is not mowing and not being charged .
. The mower To wake up the mower remotely from the energy saving
2
mode, press "Mow" in the Honda Mii-monitor App . When
a Calendar or the Honda "Smart Timer" functionality
becomes active, the wire signal will start up automatically .
Mowing small lawn areas with "Place &
Mow"
Place & Mow is intended for mowing small areas
that require special treatment without having to mow
the whole lawn, such as the area under a piece of
garden furniture that has been removed . The mower is
positioned at the lower left corner of the intended area to
mow (see figure H). The final mowed area depends on
the lawn conditions; it will not necessarily be an exact
square . After completion of "Place & Mow", follow the
instructions on the screen .
Note: For safety reasons, "Place & Mow" cannot be used
outside the perimeter wire .
Sensors
The mower is equipped with the following sensors:
– The lift-up sensor is activated when the mower is
– The rollover sensor detects when the mower tips over .
– The tilt sensor is activated when the mower reaches a
4 h
2
12 h
2
14 h
2
lifted .
slope angle of 32° .
English | 9