Related Manuals for Olivetti d-ColorMF659
Summary of Contents for Olivetti d-ColorMF659
- Page 1 Multifunction Digital Copier d-ColorMF659/MF559/MF459 INSTALLATION MANUAL Code: Y119820-3...
- Page 2 PUBLICATION ISSUED BY: Olivetti S.p.A. Gruppo Telecom Italia Strada Monte Navale, 2/C 10015 Ivrea (TO) ITALY Copyright © 20 20 Olivetti All rights reserved...
- Page 3 INSTALLATION MANUAL Applied Machines: [Important] Be sure to correctly follow the procedures in order as explained in this Installation Manual. If you do not follow the procedure in order, the image trouble may occur. 1. Outline of installation procedures HT-509 MK-734 TK-101 PC-116...
- Page 4 2. Installation space 3. Pre-installation check items (1) Select a level and stable place for installing the (Unit: mm (inch)) machine. 65C-0i/55C-0i/45C-0i + PC-417 + FS-540SD + (2) Be sure to use a power source of the voltage LU-207 and frequency indicated in the product specifi- cations.
-
Page 5: Accessory Parts
Name Shape Q’ty 5. Accessory parts 12. Chart Name Shape Q’ty 1. Installation 1 set manual 13. Cable clamp 2. Paper size la- bel *1 14. Screw A (3 x 8 3. NFC label 15. Screw B (3 x 10 mm) (black) 4. - Page 6 * Power supply 6. Installing the main body and the Paper 65C-0i: 220-240V 10A Feed Cabinet 55C-0i: 220-240V 9A 45C-0i: 220-240V 8A (1) Take the main body and the Paper Feed Cabi- net out from its packaging. Note: • This manual provides the illustrations of the CAUTION accessory parts and machine that may be slightly different in shape from yours.
- Page 7 (2) Open the right door and remove the protective 7. Removing protective tape, packing and sheet and locking materials. other shipping materials Note: (1) Remove the protective tape and the protective • After removing the locking materials, make materials. sure that the transfer roller assembly is se- cured in place.
- Page 8 (4) Slide out the tray 1. (8) Remove the four locking screws. (5) Remove the protective tapes from the inside of the tray 1 and remove accessory parts. Note: See the User’s Guide for instructions on setting paper in each tray and configuring the paper types.
- Page 9 (11) Remove the cable clamp securing the DF ca- (14) Remove the protective tape on the lower front ble. (One screw) door. (12) Secure the DF cable with the removed cable (15) Remove the four locking materials. clamp as shown in the illustration. (One re- moved screw) (16) Release the lever of the drum unit.
-
Page 10: Installing The Toner Cartridge
(17) Slightly slide the drum unit out and remove the 8. Installing the toner cartridge protective tape and protective material. Note: Since cartridge is not supplied with the machine, purchase toner cartridge separately. (1) Shake the toner cartridge up and down and left to right 5 to 10 times respectively. -
Page 11: Installing Other Options
(4) Push the toner cartridge all the way in. (2) Insert the stylus pen into the holder at the right side of the main body. Note: Make sure that the toner cartridge is pushed all Note: the way in. The attachment hole at rear of the control panel can be used to attach the stylus pen with a string. -
Page 12: Connecting The Power Cord
(5) Attach the supplied duct cover. (Two supplied (3) Plug the power cord into the power outlet. screws B) 12. Starting the machine 11. Connecting the power cord Open the power switch cover on the right side of the (1) Connect the connector of the power cord to the main body, and turn ON the main power switch. -
Page 13: Configuring Other Options
15. Unit change 17. Configuring other options (1) If any of the following options are installed, re- Note: This function allows the user to select the type of fer to the “Configuration procedures” of the in- message that will appear when the replacement stallation manual for each option and configure time arrives for each of the different units. -
Page 14: Connecting The Network Cable
<When using the Paper Feed Cabinet PC-417> 20. Connecting the network cable a) Remove the rear right cover from the paper (1) Connect the main body and networking equip- feed cabinet. (Two screws) ment (HUB) using the network cable. Note: The following shows the recommended network cables that correspond to each communication speed. - Page 15 c) Pass the cable through the notch and attach c) Route the network cable through the harness the rear right cover. (Two screws) guide and three wire saddles. Note: Leave an appropriate amount of slack in the por- tion of the cable between the plug and the har- ness guide in a manner which does not interfere with the opening and closing of the cover.
-
Page 16: Network Setting
21. Network setting 23. Affixing the labels Make the TCP/IP address setting for the network. (1) Affix the paper size labels that correspond to the sizes of paper used in each tray. Note: Consult the network administrator for the setting value to be entered and make settings as re- quired. - Page 17 24. Installing the user’s guide holder Install the user’s guide holder. Note: • When attaching the holder at the position shown in <Installation position ①> (the rear side of the main body), make sure that the stored contents such as a manual do not block the exhaust port of the duct cover.
-
Page 18: Installation Procedures
SP-501 Stamp Unit INSTALLATION MANUAL (3) Push the lock lever while releasing the tab to 1. Accessory parts open the original tray. Name Shape Q’ty 1. Stamp unit 2. Stamp 3. Installation 1 set manual (4) Remove the stamp unit cover. WARNING Keep this bag away from babies and chil- dren. -
Page 19: Configuration Procedures
(6) Mount the supplied stamp in stamp unit. (9) Place the relay connector at the location shown in the illustration and pass the stamp unit har- Note: ness through the gap of the rib. Align the round pin of the stamp with the slit in the stamp unit side. - Page 20 Olivetti S.p.A. www.olivetti.com Copyright © 2020 Olivetti All rights reserved. The manufacturer reserves the right to make changes to the product described in this manual at any moment and without giving prior warning. No part of this document may be copied, reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording or other, without obtaining prior written authorisation from the publisher.