Related Manuals for Perrot P2M
Summary of Contents for Perrot P2M
- Page 1 Maintenance and Operating Instructions Large area sprinkler Type: P2M PERROT TDP056e Rev. 03.07.2018 Page 1 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
-
Page 2: Table Of Contents
4. Assembly 5. Commissioning 6. Maintenance 7. Malfunction and trouble‐shooting 1. General We presume that you are experienced in the field of irrigation. Therefore, we have kept this instruction as brief as possible, and have included only such information which you must have for the use of this product. A guarantee can be accepted only, if the sprinkler has been operated in accordance with these instructions, and if the defect occurs within the guarantee period. 1.1. Application The sprinkler is used for the uniform distribution of the water. The water should be pre‐cleaned, and free of coarse and fibrous impurities. Max. water temperature 50°C. Max. ambient temperature 75 °C TDP056e Rev. 03.07.2018 Page 2 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ... -
Page 3: Safety
2.2. Dangers if the safety instructions are not observed Non‐observance of safety instructions can endanger persons as well as the environment and the sprinkler. Non‐observance of the safety instructions can result in a loss of all claims for indemnity. 2.3 Operator / Owner has to guarantee that there are no persons in the operation area during running of the system. Build in or erection of large area sprinkler over height of head. If not possible the use of other safety measures has to be taken. TDP056e Rev. 03.07.2018 Page 3 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ... -
Page 4: Description
For sealing the thread, hemp and a jointing compound has to be used e.g. Fermit special To screw on the sprinkler, always use a pipe wrench size 3“. Tighten the sprinkler with around 30Nm. Do not turn the sprinkler by using the jet pipe. S prinklers should be installed above head‐height, respectively adopt any alternative safety measures. Pipe wrench picture.1 Screw on the connection socket as far as it will go, so that the sprinkler cannot unscrew during operation. TDP056e Rev. 03.07.2018 Page 4 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ... -
Page 5: Commissioning
Only the rotating speed of the sprinkler has to be adjusted as well as the part circle operation for the sector, which has to be irrigated. 5.1 Adjustment of Rotation Speed (for agricultural applications) Turning the regulation screw to the right will lower the rotation speed Option: If a “K” is stamped in the speed regulation screw, the sprinkler can be stopped completely by turning the speed regulation screw to the right (from year of manufacture 2013). By turning the regulation screw to the left the rotation speed is increased. For minimal speed, the use of clear water is required. In case dirty water is used, the regulation screw has to be opened completely; otherwise the sprinkler can stop its operation. picture 2 Adjusting screw TDP056e Rev. 03.07.2018 Page 5 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ... - Page 6 Infinitely adjustable by pulling (not pressing) the relevant end of the upper or lower spring stop. The irrigated part circle has to be adjusted by the spring stops (see sketch). Setting part circle angle Infinitely adjustable by pulling (not pressing) the relevant end of the upper or lower spring stop. Spring stop Adjust here picture 3 Spring stop Full circle irrigation For full circle irrigation the spring stops have to be removed. Pull spring stops only so far apart that they can be stripped off easily. In case of overstretching, they cannot be used again for part circle operation. TDP056e Rev. 03.07.2018 Page 6 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
- Page 7 Putting into service in spring The sprinkling head of the piston drive sprinkler is, due to the load alterations and the different installation conditions (humid, dry), exposed to extreme tensions. Under these conditions the piston can get axial play. In order to avoid interruptions of service, the piston cover should be tightened up at the putting into service in spring during its first and second year of operation as described below. The cover has to be tightened up with the face spanner ZB98236 and an effort of approx. 10Nm. This means at a lever length of 10cm you have to mobilize a strength of 100N on the spanner. Note: After the 3rd and 4th winter there shouldn’t be any more expansions. Option: Before tightening up the grey cover, the safety screw has to be removed. After the adjusting of the grey cover, the safety screw has to be screwed in again. The safety screw prevents an independent loosening of the grey cover. TDP056e Rev. 03.07.2018 Page 7 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
-
Page 8: Maintenance
Stiffening ribs Attention: If the safety screw can’t be tightened up, it hits a stiffening rib of the piston drive! In this case, the grey cover has to be pulled tighter, so that the safety screw passes the stiffening rib. 6. Maintenance 6.1 Lubricate thread of jet pipe When changing the main nozzle, the thread at the jet pipe and the O‐ring seat should be cleaned and lubricated. Thus, the nozzle can be removed and fixed again easily. O‐ring Nozzle Jet pipe Outlet nozzle for control water picture 4 TDP056e Rev. 03.07.2018 Page 8 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ... - Page 9 To clean the filter, use a brush or a high pressure cleaner Filter for control water picture 5 6.3 Clean piston drive and piston drive area If the drive unit does not function due to heavy stains, the piston drive has to be removed and cleaned. 6.3.1 Remove piston drive: (see TDP055e‐rep) TDP056e Rev. 03.07.2018 Page 9 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ...
-
Page 10: Malfunction And Trouble-Shooting
Elimination Sprinkler does not rotate or The water is dirty. Open adjusting screw, dirt is just very slowly. Speed regulation is adjusted at flushed out. min. Clean filter, as mentioned Filter is blocked. under 6.2 and 6.3 Sprinkler with poor water Nozzle or jet straightener is Remove nozzle. Clean jet pipe. jet. blocked. Lubricate thread of jet pipe. Sector angle gets bigger Spring stop is loose. Assemble new spring stop. during operation Spring strength is slackened. Spring stop is overstretched. Sprinkler’s bearing is Grooved ring is worn out Repair only possible by the leaking. manufacturer Subject to change without prior notice. TDP056e Rev. 03.07.2018 Page 10 / 11 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / E‐mail: technik@perrot.de ... - Page 11 D‐75382 Althengstett – Germany Tel. +49‐(0)7051‐162‐0 Explains herby that the following product: Product description: Large area sprinkler P2M Year of launch: 2009 Corresponds to the regulations of the guidelines designated above. ...