Hazards of ignoring safety instructions Failing to heed the safety instructions may result in danger to life and limb, harm to the environment and/or damage to the device. Failing to heed the safety instructions may lead to the loss of any right to claim compensation. TDP078e.doc Rev. 30.11.2016 Page 3 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
is aligned in a straight line from the left side of the irrigation sector. A dot is located on the border of the housing cover with sod cup as an additional identification mark. Dot Alignment Left side of irrigation sector Special tools Retainer for sprinkler head Changing nozzle RT14031 Hydra L/M/S Flushing equipment Hydra M Flushing pipes RT14934 Wrench for changing nozzles Changing nozzles ZB98276 TORX‐key for screw at the lid ZB98289 TDP078e.doc Rev. 30.11.2016 Page 5 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Commissioning a) Slowly open water supply to the sprinkler until operating pressure is present. b) Once the water supply is open and the maximum operating pressure has been reached, check sprinkler and connection for leaks. Sprinkler head rises and begins to rotate. Do not stand facing the nozzle opening! Preparing for winter Before the onset of any winter frosts, the sprinkler needs to be emptied. To do this, a powerful compressor needs to be attached to the pipeline network. Then open the solenoid valve in front of the sprinkler and keep it opens until nothing but air comes out of the nozzle. This model does not have a discharge valve and can therefore not be emptied the traditional way by gravity. TDP078e.doc Rev. 30.11.2016 Page 6 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Setting irrigation sector (Part‐circle sprinklers only) Since the irrigation sector adjustment screws are located under the cover with sod cup on the Hydra M‐TC version, the cover must be disassembled to make irrigation sector adjustments. First remove the plug and then the coder fastening screw using a Torx‐key TX20. Cover fastening screw Then the sprinkler head cover with sod cup can be unsnapped by pressing it lightly rearward. Left stop position can be adjusted by +/‐ 90° Note: One complete revolution of the adjuster screw adjusts the sector stop position by 60° Right‐side stop Left‐side stop TDP078e.doc Rev. 30.11.2016 Page 7 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Page 8
Set right side stop position: Right stop position can be set to a watering sector of 30° to 330°. Note: The sprinkler has a factory setting of 180° TDP078e.doc Rev. 30.11.2016 Page 8 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Page 9
Note: In order to speed up the setting of the irrigation sector, the sprinkler head can be manually turned forward with the rotating direction. . DO NOT TURN BACK! the factory setting of the right sector stop is according this sketch Right stop Left stop position position TDP078e.doc Rev. 30.11.2016 Page 9 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Replacing the nozzle Ensure sprinkler is not under pressure. Disassemble housing cover with sod cup by unscrewing the three (3) sheet metal screws (item 1) using a Torx‐key. Pull the cover off in an upward direction Disassemble sprinkler head cover with sod cup by unscrewing the central cover mounting screw (item 2). Now the sprinkler head cover with sod cup can be unsnapped by pressing it lightly rearward (see also photo on next page). Remove white lock washer using screwdriver Pos.1 Pos.2 Retaining ring Pull sprinkler insert out of the housing Push down the flange and secure the head with the retainer TDP078e.doc Rev. 30.11.2016 Page 10 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Page 11
Rotate nozzle to the left using pliers and then pull out. Optionally the sprinkler can be assembled with a tail nozzle. This nozzle can be refitted or/and also closed with a corresponding plug. Put O‐ring over the new nozzle O‐Ring Nozzle and, reversing the procedure, re‐install in the sprinkler head. Fit cover with sod cup into sprinkler head’s snap‐in connection by first pushing it as far as it will go against the side opposite the nozzle and then snapping it completely into place on the nozzle side. Using a Torx‐key, tighten the cover fastening screw (item 2) of the cover with sod cup and plug it. TDP078e.doc Rev. 30.11.2016 Page 11 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Snap inlet nozzle back onto the sprinkler module so that the elongated rib is pointing to the nozzle diameter being used. Strainer Inlet nozzle Rib Inlet nozzle White for Hydra XS 4 Black for Hydra S + Hydra XS 5+6 Turbine for Hydra M View from above Rib Sprinkler insert Note: If you want a higher rotational speed, the rib must be pointing to a smaller diameter than that of the nozzle actually being used. TDP078e.doc Rev. 30.11.2016 Page 12 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Sprinkler insert Guide housing Guide ribs Push flange down as far as it will go. Fit retaining ring. Retaining ring must be fully inserted into the slot. Assemble cover with sod cup by mounting the cover on the guide housing such that the mark of the guide housing and cover are at the same position. Tighten the cover with three (3) sheetmetal screws (item 1). Check sprinkler is working properly as per point’s 5a‐5b. TDP078e.doc Rev. 30.11.2016 Page 13 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Cause Remedy Stop valve fails to close Bits of dirt between sealing plate Clean stop valve seat and completely and stop valve. sealing plate Rotary speed too low / too high Inlet nozzle incorrectly set (see Set inlet nozzle to correct or does not rotate at all chapter 7) nozzle diameter Turbine blocked by stones or bits Clean turbine of dirt Inlet nozzle or filter have worked Clip parts together again loose Output pressure at sprinkler Stones and bits of dirt are Clean stop valve and flush nozzle too low or casting range hindering an unimpeded flow‐ sprinkler too short through of water Subject to change without prior notice. TDP078e.doc Rev. 30.11.2016 Page 14 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...
Page 16
Für weitere Informationen stehen wir Ihnen gerne zur Verfügung. We remain at your full disposal for any further information you may require! REGNERBAU CALW GmbH Industriestrasse 19‐29 75382 Althengstett / Germany Tel. +49 / 7051 / 162‐0 Fax. +49 / 7051 / 162‐133 http://www.perrot.de TDP078e.doc Rev. 30.11.2016 Page 16 / 16 Perrot REGNERBAU CALW GmbH Industriestraße 19‐29 / D‐75382 Althengstett / Germany Phone: 0049‐7051‐162‐0 / Fax: 0049‐7051‐162–133 E‐mail: errot@perrot.de / E‐mail Technical Department: technik@perrot.de ...