Sony HDV HVR-1500 Operating Instructions Manual page 49

S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
R E P E A T M O D E : O F F
R E P E A T T O P : T . T O P
R E P E A T E N D : V . E N D
A P R E S E T
B P R E S E T
Monitor screen
5
Press the m button to select REPEAT TOP.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
R E P E A T M O D E : O F F
R E P E A T T O P : T . T O P
R E P E A T E N D : V . E N D
A P R E S E T
B P R E S E T
Monitor screen
6
Press the ,/B button.
The display changes as follows.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
R E P E A T T O P : T . T O P
* T A P E T O P
A P O I N T
Monitor screen
7
Press the m button to select A POINT.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
R E P E A T T O P : T . T O P
* T A P E T O P
A P O I N T
Monitor screen
8
Press the </A button.
The display changes as follows.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
R E P E A T M O D E : O F F
R E P E A T T O P : A
R E P E A T E N D : V . E N D
A P R E S E T
B P R E S E T
Monitor screen
9
>> REPEAT MD
Time counter display
10
>> REP TOP
Time counter display
>>> Tape top
Time counter display 11
>>> A point
12
Time counter display
13
>> REP TOP
Time counter display
Press the m button to select A PRESET.
S E T U P M E N U
O P E R A T I O N A L F U N C T I O N
R E P E A T F U N C T I O N
R E P E A T M O D E : O F F
R E P E A T T O P : A
R E P E A T E N D : V . E N D
A P R E S E T
B P R E S E T
Monitor screen
Press the ,/B button.
The A PRESET MODE screen appears. The timecode
value of the current point A is displayed below the
screen title.
A P R E S E T M O D E
A 0 0 : 0 0 : 0 0 : 0 0
R E P E A T T O P
I N C / D E C : ( ) ( ) K E Y
S H I F T : ( ) ( ) K E Y
C L E A R : R E S E T K E Y
D A T A S A V E : S E T K E Y
T O M E N U : M E N U K E Y
Monitor screen
Press the </A or ,/B button to select the digit in
the timecode value display that you want to change.
Each press of the button causes the digit to the left or
right to begin flashing.
Holding the button down moves the flashing digit
continuously.
If you want to clear the timecode value, press the
RESET (NO) button. The value is cleared to
00:00:00:00, and the leftmost digit begins flashing.
Press the M or m button to increment or decrement the
value of the flashing digit.
Each press of the button increments or decrements the
value. Holding the button down increments or
decrements the value continuously. To change other
digits, return to step 11.
Press the SET (YES) button to confirm the defined
value.
The message "NOW SAVING..." is displayed on the
monitor screen and "Saving..." is shown in the time
counter display while the new setting is being saved in
memory.
Caution
The new setting may be lost if you power off the unit
during the saving operation. Wait until the saving
operation is completed before powering the unit off.
>> A preset
Time counter display
00:00:00:00
Time counter display
49
Playback