Page 3
2 GALLON FOAM MARKER EXPLODED VIEW 2 GALLON FOAM MARKER KIT P10020 ITEM PART NUMBER DESCRIPTION MTD 2020 FOAM MARKER, 2 GALLON R22-060 SUPPORT BRACKET, FOAM MARKER R22-112 SUPPORT BRACKET, LOWER, FOAM MARKER CB-1434 CARRIAGE BOLT, 1/4 X 3/4 CB-3834SS CARRIAGE BOLT, SS - 3/8-16 x 3/4 HFSSC-145 HEX FLANGE BOLT, SS - 1/4-20 x 1/2...
Page 4
2 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP ONE: Disconnect the battery, ground first and then power wire. GROUND POWER STEP TWO: Disconnect and remove the fuel tank. CAUTION! -Beware of excess fuel in the lines. -Fuel spillage. WARNING! -Flammable gas.
Page 5
2 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS NOTE: Parts are shown in colors for clarity. STEP THREE: • Attach the foam marker support bracket (supplied with the kit) to fuel tank support. 2 CB-1434SS and 2 HFNCS- 38S (supplied with the kit). Leave the bolts loose. •...
Page 6
2 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS • Attach the foam marker assembly (supplied with the kit) to the support. Use 2 HFSSC-381 (supplied with the kit). STEP FOUR: Attach the foam marker bracket to the end of the boom. NOTE: Repeat step four for the other side of the boom, and the orientation of the bracket for left and right side.
Page 7
2 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP SIX: • Remove the plastic cap from “aux 3” in the panel and route the wiring harness down through the hole in LONG SIDE the dash panel. • Attach the “rocker switch” to the dash panel. NOTE: •...
Page 8
2 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP EIGHT: • Connect the ground wire from the wiring harness to the up right cross member. • Route the power wire neatly down and along the frame to the battery. NOTE: Do not connect the Power wire until all connec- tions are made, (see step ten) STEP NINE: Plug the pump power connector from the harness to the foam marker power connector.
Page 9
2 GAL. FOAM MARKER ASSEMBLY INSTRUCTIONS STEP TEN: • Reconnect the battery power wire first along with the yellow power wire from the wiring harness, and then reconnect the ground wire. GROUND POWER • Reinstall and connect the fuel tank. CAUTION! -Beware of excess fuel in the lines.
Page 10
2 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS STEP ELEVEN: • Connect the “y” adapter assembly to the push lock elbow fitting on the foam marker. • Using the supplied tubing and hose wrap, cut and route the tubing from the “y” adapter along the frame and up to the foam marker.
Page 11
2 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS OPERATION FILLING THE TANK CAUTION! • Wear safety goggles & all proper clothing when operating, servicing or refilling this machine. • Always read & follow manufactures recommendations when handling any chemical. • Do not pump combustible liquids or vapors with this product. •...
Page 12
2 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS • Start the machine and activate the foam marker and let it prime until it starts dropping suds. • Turn the foam marker and machine off, Adjust the foam marker for desired timing. - Flow control valve, •...
2 GAL. INDEPENDENT SPRAYER ASSEMBLY INSTRUCTIONS TROUBLE SHOOTING PROBLEM SOLUTION • ADD MORE FOAM CONCENTRATE TO THE TANK. • CHECK FOR HOLES IN THE AIR LINE. • NOT ENOUGH FOAM CHECK FOR PINCHED AIR OR LIQUID LINES. • CLEAN SCREEN-STRAINER/FOAM HEAD. •...
Need help?
Do you have a question about the SG42 and is the answer not in the manual?
Questions and answers