Astronergy Chint Solar CHSM6610M Manual
  1. Manuals
  2. Brands
  3. Astronergy Manuals
  4. Solar panel
  5. CHSM6610M
  6. Manual

Astronergy Chint Solar CHSM6610M Manual

Hide thumbs Also See for Chint Solar CHSM6610M:
Table of Contents

Advertisement

Quick Links

Crystalline Silicon PV
Module Installation
Manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Chint Solar CHSM6610M and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Astronergy Chint Solar CHSM6610M

Summary of Contents for Astronergy Chint Solar CHSM6610M

  • Page 1 Crystalline Silicon PV Module Installation Manual...

  • Page 2: Table Of Contents

    Catalogue Introduction................................3 1.1 Purpose.................................3 1.2 Scope of liability..............................3 Regulations................................3 Safety Precautions..............................3 3.1 General safety..............................4 3.2 Operation safety measures........................... 5 Handling and unpacking............................. 6 4.1 Transport................................6 4.2 Unpack................................. 7 4.3 Stack..................................7 Mechanical installation............................7 5.1 Environment.................................7 5.2 Tilt angle selection...............................

  • Page 3: Introduction

    manual is complied with is beyond the control of Chint Introduction Solar. Chint shall not be liable for any form of loss, including but not limited to loss, damage, casualty or We appreciate for your trust and confidence towards additional cost caused by improper installation, the photovoltaic (PV) module products manufactured operation, use and maintenance of PV modules and by Chint Solar.

  • Page 4: General Safety

    diodes, junction boxes, connectors, etc.). Read and understand all safety instructions before installing, wiring, handling, and/or maintaining PV It is forbidden to plug in connectors of different  modules. modules generate direct current types and models. electricity when they are exposed to sunlight or other light sources.

  • Page 5: Operation Safety Measures

    period of time, otherwise the temperature of the electric shock; if it is installed far above the ground, shaded module may rise due to hot spot effect, please wear a seat belt. burning the module and causing fire hazard in When operating PV modules in the sun, please use ...

  • Page 6: Handling And Unpacking

     Do not disconnect the electrical connection when If the PV module is not in use, please do not open  there is a load. the product packaging. The goods should be stored in a dark, dry and ventilated place. If the PV ...

  • Page 7: Unpack

    when the PV modules are removed from the container, metal corrugated, etc. the distance between the upper surface of the forklift When the PV modules are stacked, they must be neatly tines and the ground should be less than 80mm, and stably stacked on a horizontal surface, and stacked otherwise collisions may easily occur, which may with the glass side of the bottom module facing up and...

  • Page 8: Tilt Angle Selection

    extreme operating ambient temperature for PV module is maximized. when it faces the sun directly. modules: -40 °C to 85°C.  Mechanical load on PV modules: under standard installation conditions, maximum tested snow/wind load is 5400 Pa/2400 Pa and the design load (considering a safety factor of 1.5 times) is 3600 Pa/1600 Pa.

  • Page 9: Bolted Mounting

     The PV module must be securely fastened to the mounting system. If the PV module is mounted in a snowy area, the height of the mounting system should be designed in a way that the lowest end of the PV module is not covered by snow. In addition, it should be ensured that the lowest end of the PV module is not shaded by surrounding trees or other Fig 3.

  • Page 10: Clamped Mounting

    Fig. 7 Diagram of the bolt installation process Fig. 8 Rails vertical to the long-side frame Place the PV module on top of the rack. Insert 4 stainless steel bolts in corresponding mounting holes. The 9x14mm mounting holes match with M8 bolts, while the 7x10mm mounting holes match with M6 bolts.
  • Page 11 the glass and should not deform the frame, otherwise they may cause module damage. Be sure to avoid shadowing effects from the module clamps. Weep holes on the module frame must not be closed or obscured by the clamps. The clamp must have at least 8mm but no more than 11mm overlap with the frame of the module (The Fig.
  • Page 12 Figure 13 Mounting requirements for rails overlapping the short-side frame Table 1 Installation range and corresponding values Installation method Module Module type Fig 2 & Fig 3 dimension Fig 5 Fig 8 Fig 9 Fig 6 & Fig 4 L*W*H (mm) +5400/-2400Pa +2400/-2400Pa 1648*990*35...
  • Page 13 Table 1 (continue) Installation method Dimensions Module type Fig 2 & Fig 3 L*W*H (mm) Fig 5 Fig 8 Fig 9 Fig 6 & Fig 4 +5400/-2400Pa +1800/-1800Pa +5400Pa Installation scope Installation scope 1755*1038*30 CHSM60M-HC -2400Pa 350±50mm 200±50mm CHSM60M(BL)-HC +5400/-2400Pa CHSM60M/LV-HC +5400Pa 1755*1038*30...

  • Page 14: Electrical Installation

    2094*1038*35 -2400Pa -2400Pa Installation scope -2400Pa 400±50mm +Bumper +5400/-2400Pa +5400Pa 2094*1038*30 Installation scope -2400Pa 350-400mm +5400/-2400Pa +1800Pa +5400Pa +2400Pa 2256*1133*35 Installation scope -1800Pa -2400Pa -2400Pa 400~450mm +Bumper +5400/-2400Pa +1800Pa +5400Pa 2278*1134*35 Installation scope -1800Pa -2400Pa 400~450mm +Bumper +2400/-2400Pa Installation scope +5400Pa 400~500mm +1800Pa...

  • Page 15: Electrical Connection

    To ensure the normal operation of the system, make -36 ~ -40 1.25 sure the polarity of cables is correct when connecting modules or loads, such as inverters and batteries. If the Alternatively, a more accurate correction factor for the Voc can be calculated using the following formula: PV module is not connected correctly, the bypass diode may be damaged.

  • Page 16: Grounding

    conditions. Avoid exposing connectors to direct Fig. 14 Schematic diagram of electrical connection sunlight and soaking in water. Avoid the connectors falling on the ground or the roof. Do not plug or ！ATTENTION unplug the connectors when the PV module is in ...

  • Page 17: Maintenance

    Use UL-467 certified bonding and grounding  devices, including Burndy (formerly Wiley Electronics) Washer Electrical Equipment Bonding (WEEB) and similar devices, such as barbed washers, that meet the requirements of UL-467 and is suitable for electrical bonding and grounding of PV modules.

  • Page 18: Pv Module Cleaning

    PV modules without authorization. When conducting module (as the rainfall will provide a self-cleaning inspection or maintenance in term of the electrical and effect). If there is a large accumulation of dirt on the mechanical performance, it is recommended that PV module surface that has seriously affected the qualified professionals perform the work to avoid power production, the module can be rinsed with water...

  • Page 19: Modified Version And Date

    Modified version and date · Rev 1.0, released in June 2018. · Rev 1.1, released in July 2020. · Rev 1.2, released in October 2021. CHINT SOLAR (ZHEJIANG) Co., Ltd. Add: 1335 Bin’an Rd, Binjiang District, Hangzhou, China 310053 Tel: 86-571-5603 1888 Fax: 86-571-5603 2333 http://energy.chint.com/...

This manual is also suitable for:

Chint solar chsm6610mblChint solar chsm6610m/hvChint solar chsm60m-hcChint solar chsm60mbl-hcChint solar chsm6610pChint solar chsm6610p/hv ... Show all

Table of Contents