Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for jbc NAU
Summary of Contents for jbc NAU
- Page 1 INSTRUCTION MANUAL Nano Control Unit...
-
Page 2: Packing List
This manual corresponds to the following references: - NAE-9C (100V) - NAE-1C (120V) - NAE-2C (230V) Packing List The following items are included: Nano Control Unit ........1 unit Cable Collector and Stand ....2 units Ref. CC2002 Brass Wool ..........1 unit Metal Brush .......... -
Page 3: Features And Connections
Features and Connections Cable collector Accessorie: Tool extension cord (1m)* Ref. A1205 Stand: Intelligent Heat Management Nano Handle* Process Ref. NT115-A Screen: 2.8 Color TFT Cartridge Extractor Adjustable Tip Aligner Nano Tweezers* Ref. AN115-A Metal brush Brass wool USB-A Connector USB-B Connector Main Switch... - Page 4 Tool Stand Assembly Tool Stand Replacement Loosen the screw (1) and withdraw the tool Insert the new tool stand (3) and tighten the stand (2). screw (4).
-
Page 5: Work Screen
Work Screen NAS offers an intuitive user interface which provides quick access to station parameters. Default PIN: 0105 Status Bar 17:14 Tool NT115 in use ºC Power Temp. Levels indicator Power Port Displayed if temperature levels are activated Station Information Change port Menu Options... -
Page 6: Advanced Functionalities
Insert a USB flash drive into the USB-A connector to save your soldering process in csv format. Files Station update Download the JBC Update File from www.jbctools.com/software.html Insert the USB flash drive with the file downloaded to the station. Update System Notifications The following icons will be displayed on the screen’s status bar. -
Page 7: Operation
Operation JBC’s Exclusive Heating System This revolutionary technology is able to recover tip temperature extremely quickly. This allows the user to work at a lower temperature. As a result, tip life increases by 5. 1. Work 2. Hibernation When the tool is lifted from the holder the tip When the tool is in the holder, the power will heat up to the selected temperature. - Page 8 Chip Components Rework Process using Tweezers* and Pedal* The Adjustable Nano Tweezers is the most effective tool for desoldering chip components but also it facilitates its rapid placement and soldering by using the P-405 pedal connected to the station. Adjustable Nano Tweezers* Ref.
- Page 9 For this operation JBCs desoldering station* is needed. Solder Paste Dispensing Manual Solder Paste Apply the solder paste amount needed to Dispenser* solder the new chip component. Ref. DPM-B The use of JBC´s DPM Manual Solder Paste Dispenser* is recommended. * not included, sold separately...
- Page 10 Placing Do not press the pedal. Use the tweezers to position the component on the previously tinned pad. Note: The inactive tool prevents the component from heating up prematurely. Soldering Once in position press and hold the pedal to activate the tweezers and perform the soldering.
-
Page 11: Changing Cartridges
Changing Cartridges Save time and change cartridges safely without having to switch the station off. 1. Removing 2. Inserting 3. Aligning Place the cartridge into the Push the cartridge into the Use the holes to rotate extractor slot (1) and pull the handle until the mark*. -
Page 12: Maintenance
2. Press the new fuse into the fuse holder fuse. If necessary use a tool to lever it off. and replace it in the station. Fuse holder Fuse holder Fuse - Repairs should only be performed by a JBC authorized technical service. - Page 13 Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use.
- Page 14 Notes...
-
Page 15: Specifications
Specifications Nano Control Unit Ref. NAE-9C 100V 50/60Hz. Input fuse: 0.5A. Output: 8.5V Ref. NAE-1C 120V 50/60Hz. Input fuse: 0.5A. Output: 8.5V Ref. NAE-2C 230V 50/60Hz. Input fuse: 0.2A. Output: 8.5V - Output Peak Power: 14W per tool - Temperature Range: 90 - 450 °C / 190 - 840 ºF - Idle Temp. - Page 16 In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased. Get 1 extra year JBC warranty by registering here: https://www.jbctools.com/productregistration/ within 30 days of purchase. This product should not be thrown in the garbage.