Related Manuals for Directed 403.CHRYSLER6 v2.17
Summary of Contents for Directed 403.CHRYSLER6 v2.17
- Page 1 403.CHRYSLER6 v2.17 2014 Dodge/Ram 3500 THCHD3, THCHD3-REV2 Compatible (Sold Separately)
-
Page 2: Table Of Contents
Contents Introduction Vehicle function compatibilities Pre-installation and application warnings Installation Wiring diagram with T-Harness (THCHD3 Rev. 1 to 2) Wiring diagram Locating components in the vehicle Vehicle connections SmartStart/XL202 installation notes Connecting the module LED diagnostics and troubleshooting Soft reset Hard reset Module programming Feature programming... -
Page 3: Introduction
Introduction DB3 is an all-in-one door lock and override module. This guide supports the installation of a DB3 in Range Extender Ready (RXT) mode with an RF System or a SmartStart (both sold separately). Warning! This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. -
Page 4: Vehicle Function Compatibilities
Vehicle function compatibilities This section lists all the functions compatible with this vehicle for the installation illustrated in this guide. Note: The telematics features listed below (with an asterisk) ONLY apply when using SmartStart. Panic Mode Activation RAP Shut Down (Retained ACC Power) Parking Lights Control Remote Start Ready Arm Factory Security... -
Page 5: Pre-Installation And Application Warnings
Pre-installation and application warnings This section highlights important information for this specific firmware and will assist in pricing accordingly, as START HERE well as bringing awareness to any operational or vehicle limitations. Compatibilities and Requirements THCHD3 (Rev. 1 to 2) T-Harness Keys required for Keys required... -
Page 6: Installation
Wiring diagram with T-Harness (THCHD3 Rev. 1 to 2) Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( OBDII Diagnostic Connector Not Used Female Female Male Male T-01 T-02 6-pin Black Connector... -
Page 7: Wiring Diagram
Wiring diagram Refer to "Pre-installation and application warnings" for important information, such as the description of each special note referenced in the diagram ( OBDII Diagnostic Connector (-) Ground: pin 4 CAN C High: CAN IHS High: Gray/White, pin 6 Gray, pin 3 (+) 12V: Red, pin 16 You can connect to either a... -
Page 8: Locating Components In The Vehicle
Locating components in the vehicle 403.CHRYSLER6 2.17 2014 Dodge/Ram 3500 ©2022 VOXX•DEI LLC. All rights reserved. -
Page 9: Vehicle Connections
Vehicle connections The connection information listed below is specific to the 2014 Dodge/Ram 3500. Refer to “Pre-installation and application warnings” for a list of important notes. Data 14-pin blue connector (H1) Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H1/1 Light Green... - Page 10 Module Connects To Conn./Pin Color Description Wire Location (+/-) Wire Color H3/1 Green No Connection No Connection H3/2 Blue No Connection No Connection H3/3 Red/White No Connection No Connection H3/4 White/Violet No Connection No Connection H3/5 Violet/Black No Connection No Connection H3/6 White/Black The installation of an aftermarket hood pin is on...
-
Page 11: Smartstart/Xl202 Installation Notes
SmartStart/XL202 installation notes The DB3 Range Extender Ready (RXT) solution offers two (2) configuration options to control your system: RF System or SmartStart (both sold separately). This section provides specific installation information for SmartStart and XL202. SmartStart revision A SmartStart is optional and not included. It MUST be purchased separately. Configuration wires (White &... -
Page 12: Connecting The Module
Connecting the module Important! Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior to moving onto programming. Note: Before connecting either the XL202 or SmartStart module to DB3, it is important to ensure that the proper feature and function programming is selected using DirectLink (version 4.5 or higher). -
Page 13: Led Diagnostics And Troubleshooting
LED diagnostics and troubleshooting This section provides LED diagnostics and troubleshooting information to guide you through the various stages of your installation. Module Programming Description Troubleshooting Make sure the D2D harness is connected and that 12 Volt is present between the red and black wires. If Module has no power. - Page 14 Active Ground When Running (Status) Description Troubleshooting Ground When Running (Status) command The module has initialized the remote start sequence. received. Flashes green Ignition ON command received. The module has received the Ignition ON command and is processing the remote start sequence. Flashes red &...
-
Page 15: Soft Reset
Soft reset A module reset will only erase the steps perfomed in “Module programming”. The firmware and settings flashed to the module will not be affected. Connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module. (12-pin) (Button) (10-pin) -
Page 16: Module Programming
Module programming Refer to “LED diagnostics and troubleshooting” for more information and for troubleshooting purposes. Ensure vehicle is in a safe location and cannot move forward during programming. For vehicles equipped with a manual transmission, make sure the gearshift is in the neutral position. -
Page 17: Feature Programming
Feature programming To enter feature programming routine: 1. Turn the ignition ON, then OFF. 2. Within 5 seconds, press and hold the programming button until the LED turns ON orange (after 3 seconds). 3. Release the Programming button. 4. The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (e.g. -
Page 18: Feature And Option List
Feature and option list It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page at www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page. -
Page 19: Limited One Year Consumer Warranty
This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. -
Page 20: Quick Reference Guide (Customer Copy)
OEM remote starter. Some of the SmartStart compatible advantages of RXT are greater remote range and 2-way compatibility. This system is compatible with Directed SmartStart. For a complete list of supported features, RXT Operations please visit www.mysmartstart.com. - Page 21 The application enables a “Cloud-Connected Car” like never before, providing 2-way interaction with your vehicle. Connectivity is managed through the Directed Cloud Services (DCS) network linking car, app, end user, and the Internet. For more information, visit www.mysmartstart.com. Notes 403.CHRYSLER6 2.17 2014 Dodge/Ram 3500...