Maintenance And Troubleshooting; Maintenance Intervals; Aintenance Intervals - Climax CM6200 Operating Manual

5

MAINTENANCE AND TROUBLESHOOTING

IN THIS CHAPTER:
5.1 M
AINTENANCE INTERVALS
5.2 M - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -98
AINTENANCE TASKS
5.2.1 C
HECK THE PNEUMATIC CONDITIONING UNIT EMERGENCY STOP
5.2.2 C
HECK THE PNEUMATIC CONDITIONING UNIT DROP
5.2.3 M
AINTAIN THE ROTARY TABLE AND DRIVE ASSEMBLY
5.2.4 R PLC
EPLACING THE
5.2.5 D
RAG BRAKE SETTINGS
5.2.6 A
DJUSTING THE DRAG BRAKE
5.3 R
ECOMMENDED LUBRICANTS
5.3.1 M
AIN RING GEAR LUBRICATION
5.3.2 L
INEAR RAIL MAINTENANCE
5.4 T - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 105
ROUBLESHOOTING
5.4.1 T
HE MACHINE ISN
5.4.2 T
HE MACHINE ISN
5.4.3 T
HE MACHINE IS CUTTING POORLY
5.4.4 T
HE MACHINE ISN
5.4.5 T '
HE SPINDLE ISN
5.4.6 T
HE MACHINE STOPS SUDDENLY
5.4.7 T
HE CUT DEPTH CHANGES INVOLUNTARILY
5.4.8 T
HE SERVO SYSTEM ALARM OR WARNING
5.5 MR-J3
SERVO AMPLIFIER ERROR CODES
5.1 M

AINTENANCE INTERVALS

P/N 63674, Rev. 9
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -97
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -99
BATTERY
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 100
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 100
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 102
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 104
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 104
' - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 105
T TURNING
'
T FEEDING OR IS SLOW AND UNRESPONSIVE
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 105
' - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 106
T CUTTING FLAT
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 106
T TURNING
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 106
- - - - - - - - - - - - - - - - - - - - - - - - - - - 106
- - - - - - - - - - - - - - - - - - - - - - - - - - - 106
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 107
CAUTION
Failure to properly clean and maintain the machine can result in
machine damage and void the warranty.
Always keep chips away from moving machine parts.
Following the maintenance schedule described in Table 5-1 on page 98 is critical
to obtain normal machine life. Keep all machine components in clean working
condition.
Check that parts like the mounting surfaces, hydraulic fittings, and the tools them-
selves are free of metal chips, nicks or burrs. To prevent corrosion, thoroughly
rinse any machine parts that are exposed to salt water with fresh, clear water.
- - - - - - - - - - - - - - - - - -98
- - - - - - - - - - - - - - - - - - -98
OUT CIRCUIT
- - - - - - - - - - - - - - - - - - - - - - -99
- - - - - - - - - - - - - - - - - - 105
Page 97