Table of Contents
Advertisement
Note
Do not remove a "Memory Stick" while the "Memory
Stick" access indicator is lit. Doing so may cause a loss of
data.
b DC IN (DC power input) connector (XLR type, 4-
pin, male)
To operate the camcorder using an AC power supply,
connect an AC-550 AC Adaptor with the DC output cable
supplied with the adaptor.
c AUDIO IN CH-1/CH-2 (audio input channel 1/2)
connectors (XLR type, 3-pin, female) and input
selection switches
Connect other audio equipment or external microphone.
Set the input selection switches as shown below according
to the microphone or equipment.
LINE (left position): For connecting an external audio
signal source such as a stereo amplifier
MIC (center position): For connecting any microphone
other than 48 V microphone
MIC +48V ON (right position): For connecting a 48 V
microphone
Signals input to the AUDIO IN CH-1 connector can be
recorded on audio channels 1 and 3. Similarly, signals
input to the AUDIO IN CH-2 connector can be recorded on
audio channels 2 and 4.
1) When the AUDIO IN (CH-1/CH-2/CH-3/CH-4) switches on the side
control panel are set to "REAR" or "R".
Note
If MIC +48V ON is selected for a microphone other than
48 V microphone, the microphone may be damaged.
d
(i.LINK) DV OUT S400 connector (6-pin, IEEE
1394 compliant)
Connect to a device supporting the DV format or a
computer, using an i.LINK cable (DV cable).
Notes
• If video and audio signals are not output from the
external device connected to the
S400 connector, disconnect the i.LINK cable (DV cable)
and then reconnect it, making sure that it is firmly seated.
• When you connect the camcorder and other equipment,
such as a hard disk drive, with an i.LINK interface to a
computer with i.LINK connectors, turn off the power of
the computer, the other equipment, and the camcorder
before connecting them using the i.LINK cable (DV
cable). If a bus-powered type
equipment is connected while the computer is powered
on, electric current flows into the camcorder because of
the high voltage caused by the load shift of the computer
power, and this may cause a malfunction.
24
Location and Function of Parts
1)
(i.LINK) DV OUT
1)
hard disk drive or similar
1) Equipment that can be powered through i.LINK cable (DV cable)
e REMOTE connector (8-pin)
Connect an RM-B150/B750 Remote Control Unit, which
makes it possible to control the camcorder remotely.
Note
Before connecting/disconnecting the Remote Control Unit
to/from the camcorder, be sure to turn off the camcorder
POWER switch.
f DC OUT 12V (DC power output) connector (4-pin,
female)
Supplies power for a WRR-861/862 UHF Synthesized
Tuner (optional) (maximum 0.2 A).
Do not connect any equipment other than the UHF
synthesized tuner.
g AUDIO OUT connector (XLR type, 5-pin, male)
Output the audio signals recorded on audio channels 1 and
2 or audio channels 3 and 4. The audio signals are selected
by the MONITOR switch.
h SDI OUT connector (BNC type)
Outputs an HDSDI or SDI signal (with embedded audio).
To switch between HDSDI and SDI output, use the SDI
OUTPUT SEL item on the OUTPUT page of the
OPERATION menu.
Note that when the selected signal format is HDSDI, this
connector outputs no signal if you try to play back video
recorded in the DVCAM format.
During recording and playback of HD 23.98P
signals
You can select 59.94i signals after 2-3 pulldown, or
23.98PsF signals. To switch between these signals, use the
23.9P OUTPUT item on the FORMAT page of the
OPERATION menu.
Advertisement
Table of Contents
