Dancing Wings Hobby VX14 Instruction Manual

VX14 BLERIOT XI
INSTRUCTION MANUAL
W
B L
各部件用美工刀从板材上取下，按下图图示及步骤拼装，木质部件建议用
快干胶(502)定型，用白乳胶加固。
Pls take down the parts from the board by knife,and assemble
them as per the procedures as below,we suggest you to shape
with 502 glue,and firm withwhite latex.
1.机身组装 Fusalage Installation
1.1 1.2
C1
F3
F3
F1
D1
1.3
F4粘到机身末端，对齐两侧板。
Stick the F4 to the fuselage end, and align the
U1
2pcs side plate.
1.4
F7
F8
F9
C2
1.5
1.6 1.8
F11
F15
F12
G1
G1
1.7
F14
F13
对齐
Align
2.机轮及滑橇组装 Landing Gear Installation
2.1
材质 Material:
1. 椴木 Basswood
2. 巴尔莎木 Balsawood
3. 桐木 Paulownia
4. 碳杆和其他
and others
carbon rod
工具 Tools Needed
2.４
B
F3-1
C1
F3-1
F2
F3-1
F4
F5
截取2根70mm 碳杆，如图安装。
Cut two 70mm carbon rods
对齐
F6
and assemble as picture
Align
shown.
3.机翼组装 Wing Installation
3.1
C2
粘C2上端板时调整机身后端角度。
L3
Adjust the rear angle of the fuselage
when you stick the C2 upper plate.
1.9
3.2
G2
G2-1
2.2
W
G10
2.3
G4
组装2个
Assemble 2 pcs
2.5 截取1根83mm 碳杆，如图安装。
Cut one 83mm carbon rod and
assemble as picture shown.
G3
G3
B
G4
注意：此处机轮为可转动设计，请勿粘固机轮。
Note: the wheel is rotatable ,please do not stick the wheel.
2.6
G8
G5
G6
F7
F8
L1
在平整工作台面拼装L1-L3，保持机翼平直。
Assemble L1-L3 on a flat work desk and
keep the wing straight.
L2
W5
W4
W3
W1
W1
W1
W2
W1
W1
W1
3.3
从LX取下木条，安装到机翼翼梁卡口内，按实际长度截取。
Remove the wood strip from LX, install them into the wing
beam bayonet, and cut them according to the actual length.
G3
正面
G3
front
组装4个
Assemble 4 pcs
背面
back
G9
3.4
G9
12mm
左右机翼拼装方法相同，注意:请对称拼装，不要拼成顺边。完成后机翼相对插到机身。
The left and right wings are assembled in the same
instead of along the edge.After completion,insert the wings into the fuselage
3.6
4.尾翼组装 Tail Assembly
4.1
W1
W1
截取20mm 碳杆，
如图安装。
Cut one 20mm
carbon rod and
install as picture
F10
shown.
R2 不粘 Non-stick
粘固 Stick
按实际长度截取3根短木杆，如图
粘贴安装并打磨棱角。
Cut three short wooden rods
by actual length,paste as
picture and polish the edges.
3.5
way.Note:please assemble symmetrically
4.2
R1
粘固 Stick