Dancing Wings Hobby Wright Flyer I Instruction Manual

飞行者�号 安装说明
莱特兄弟 ���� 飞行者一号
The Wright Brother's 1903 Wright flyer
机翼安装介绍
Assemble the wing
细节 Detail
4
细节 Detail
2
细节 Detail
1
1
机翼前缘，后缘和翼尖的安装
Installation for the leading edge and
trailing edge of the wing and wing tip.
注意： 弯曲的翼尖务必和机
翼尖
翼保持一致水平 Wing Tip
Note: The curved tip must
be consistent with the
请注意机翼主梁的正反
wing
Please pay attention to the
front and back of the main
beam of the wing
8
细节 Detail
8
卡位
Slot
11
请注意对齐上
下翼撑
Pay attention
to aligning
the upper
and lower
struts
请勿过度用力
Pls do not
plug hard
请注意每一段的间距
Please note the spacing
of each segment
请自备以上工具
Tool Needs
Wright Flyer I INSTRUCTION MANUAL
此处以下机翼拼装为例，所有木件均从Down1-2
木板上取下，用美工刀辅助取下，然后请按步骤
拼装，各部件结合处用快干胶水粘合。
Here, take the following wing assembly as an
example. All the pieces are removed from the
Down1-2 board by knife,then the parts are
assembled according to the steps, and the joints
4
of the parts are bonded with quick-drying glue.
机翼主梁 右
Main beam of
the wing(right)
机翼主梁 右下角
机翼主梁 左下角
2
Wing's main beam
Wing's main beam
(bottom right)
(bottom left)
26
25
机翼主梁连接件
Connection of wing's main beam
9
注意主梁的正反
Please pay attention to the front
and back of the main beam
5
5
请注意卡位位置
Pay attention to the
slot position
请注意卡位位置
安装孔位在主梁下面
Pay attention to the
Mounting holes below
slot position
the main beam
安装孔位在主梁下面
Mounting holes below
the main beam
完整的机翼大梁
Completed main
beam of the wing
两片翼肋
2pcs wing ribs
完整的机翼大梁
Completed main
beam of the wing
4
3
3
4
3
完成步骤10后，下机翼拼装完成。安装步骤示范为下机翼，上机翼的安装与下机翼基本相同，安装上机
6
翼时所有木件均从Up1-2木板上取下。上下机翼的区别在主梁上，具体区别见下图，拼装时请注意。
After completing step 10, the lower wing assembly is completed. The installation steps are
10
shown as the lower wing. The upper wing is installed in the same way as the lower wing.
When the wing is installed, all the pieces are removed from the Up1-2 board. The difference
between the upper and lower wings is on the main beam. The specific difference is shown in
the picture below. Please pay attention when assembling.
5
安装孔位在主梁下面
Mounting holes below
the main beam
两片组合的翼肋仅用在机翼中部加强，其他的翼肋安装处
仅需要1片即可，除非有特别的标注。 所有的翼肋均是通
用无编号的。
Two unnumbered ribs combination use only in the
middle of the wing,each of the main wing only
need one.Unless specially marked ribs,all the rest
机翼大梁中心
ribs are unnumbered.
Center of the wing beam
翼肋
unnumbered
wing ribs
翼肋
wing ribs
7
机翼主梁 左下角
Wing's main beam
(bottom left)
6
5
翼尖
Wing Tip
请注意机翼主梁的正反
Please pay attention to the
front and back of the main
beam of the wing
24
机身和两片水平尾翼的拼装展示
12
Assembly of the fuselage and
two horizontal tails
15
24
13
24
5
翼肋
unnumbered
wing ribs
2
1
6
注意：翼尖处的翼肋编号为1、2。
Note: The ribs at the wing tip
are numbered 1, 2.
另一边相同安装
Same installation on the
other side.
26*2
26*2
22
21
21
机身/上水平尾翼
Fuselage/Upper horizontal tail