Download Print this page
Valcom PagePac V-5331215A Quick Start Manual
Valcom PagePac V-5331215A Quick Start Manual

Valcom PagePac V-5331215A Quick Start Manual

40 watt explosion proof horn

Advertisement

Quick Links

PagePac
by
INTRODUCTION
Explosion Proof Horn Speakers are constructed
so that all electrical components are sealed from
the atmosphere and may be used in areas where
flammable substances are present. The explosion
proof speakers require some assembly before
installation (see Figure 1).
Explosion proof speakers are mounted, using the
U-shaped mounting bracket (attached to each
speaker). These brackets are intended primarily
for mounting on flat surfaces, and each bracket
has three holes which may be used for installing
mounting hardware. Speaker position in the verti-
cal axis may be adjusted by loosening the bolts
that secure the bracket to the speaker body
(see Figure 1).
SPECIFICATIONS
FEATURES
• UL/CSA Approved
• Heavy Duty Construction
• Omni-Directional Mounting Bracket
• 5 Tap Settings (2.5W, 5W, 10W, 20W, 40W)
Nominal Specifications
• Dispersion: Wide Angle
• Input: 70.7V Line
• Output: 101dB - 113dB
Dimensions/Weight
• 16.5"Dia. x 21.5"D
(41.9cm x 54.6cm)
• 27 lbs. (12.2 kg)
Environment
• Temperature: -4 to 131° F (-20 to 55° C)
• Humidity:
Technical Manuals Online! - http://www.tech-man.com
Technical Manuals Online! - http://www.tech-man.com
®
40 WATT EXPLOSION PROOF HORN
0 to 95%
firealarmresources.com
V-5331215A
INSTALLATION
MOUNTING
Separate the horn and the base of the speaker by
holding the base of the speaker tightly and turning
the horn counterclockwise (see Figure 1, View 1).
Separate the two halves of the speaker base by
removing the eight bolts (see Figure 1, View 2).
Make the conduit entry into the speaker as
required by local ordinances for the class and type
of speaker used (see Figure 1, View 3).
On the speaker cable, separate the inner wires for
a distance of 3 or 4 inches by stripping away insu-
lation from the main cable. If using shielded cable,
the inner wire without insulation is the shield wire.
Strip approximately 1/2 inch of insulation from the
end of each of the smaller insulated wires.
Note: The cable must enter the speaker through a
conduit that has been installed according to local
ordinances for the class and type of speaker
used.
Connect the wires on terminals 1 and 2. If
shielded cable is used, either splice the shield
wire to provide a continuous shield to the next
speaker, or clip the shield wire at the point where
it emerges from the main cable, as appropriate.
The shield wire should not be terminated on the
speaker.
1
Issue 1
947190

Advertisement

loading
Need help?

Need help?

Do you have a question about the PagePac V-5331215A and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Valcom PagePac V-5331215A

  • Page 1 ® PagePac Issue 1 40 WATT EXPLOSION PROOF HORN V-5331215A INTRODUCTION Explosion Proof Horn Speakers are constructed so that all electrical components are sealed from the atmosphere and may be used in areas where flammable substances are present. The explosion proof speakers require some assembly before installation (see Figure 1).
  • Page 2 The numbers on the terminal strip indicate the 427-3900 and ask for PagePac Technical Sup- output in watts for a 70-volt paging system (on a port, or call (540) 427-6000 for Valcom 24-hour 25-volt paging system, the output will be approxi- Automated Support. Visit our websites at mately 1/8 of that indicated (see Table 1)).