Related Manuals for Ultra Start 2000 Series
Summary of Contents for Ultra Start 2000 Series
- Page 1 Installation Guide 2000 Advanced Alarm & Remote Starter SUPPORT Toll Free: 1-866-698-5872 email: support@ultrastarters.com web: www.ultrastarters.com WWW.ULTRASTARTERS.COM VERSION 012201...
-
Page 2: Transmitter Programming
TRANSMITTER PROGRAMMING STEP 1 - Open the hood. STEP 2 - Turn ignition key ON-OFF-ON-OFF-ON Leaving Key ON. STEP 3 - Hold brake down until lights flash and LED’s come on solid. About 5 seconds. STEP 4 -Siren/horn will chirp 5 times and leds will stay on solid. STEP 5- Press the lock button on each transmitter to be programmed. -
Page 3: Shock Sensor
2000 Series BASIC INSTALLATION - QUICK START STEP 1 - The following wires MUST be connected for proper operation. 6 Pin Power Connector - Connect the following: WIRE FUNCTION Connect to on Vehicle RED-1 Main Power Input Constant 12V (+) at Ignition Harness... -
Page 4: Park Lights
2000 SERIES WIRING DIAGRAM 30 Amp (+) Input Connect to Constant 12V+ Power Connect to Heater Fan 30 Amp (+) Out Heater Green Connect to Starter 30 Amp (+) Out Yellow Starter (-) Input Black Ground Connect to Ground 30 Amp (+) Out... -
Page 5: Pin Connector
14 PIN CONNECTOR White: +12 VDC Output for Flashing Parking Lights 15Amp Connect this White wire to positive side of the parking lights wire Red/White: 2nd Channel Output (Trunk Release) This Red/White wire supplies 500ma (-) output when button # 2 is pressed for 1 ½ seconds. Note: This can also be used for Driver’s Door Unlock priority. - Page 6 TRANSMITTER PROGRAMMING Transmitter Programming Note: The system is capable of learning up to 3 different transmitter codes. To place the system in Transmitter Code Learning Mode: 1. Open the hood. 2. Start with ignition key in the “Off” position, turn the ignition key “On/Off”, “On/Off”, “On”...
-
Page 7: Manual Transmission Mode
TACH LEARNING MANUAL TRANSMISSION Tach Leaning- Method 3 Tach learning is optional. It is only necessary if the tach sense option is selected as the desired start detection method. The black/white tach wire must be connected to a tach source. The following steps are also necessary for tach learning. 1. - Page 8 PROGRAMMING - Installer Program Mode This system is capable of multiple programmable functions. To Enter Installer Program Mode: 1. Open the hood. 2. Turn the Ignition Key “On/Off”, “On/Off”, “On”. 3. Press & Release the button on the antenna once. The system will respond with one siren/horn chirp and light flash to confirm it is in Program Mode and is ready for Feature Programming.
- Page 9 PROGRAMMING - Installer Program Mode Feature 1 - Sensing Method - Default: Voltage Sensing Press Button 3 Tach Method Confirmation 1 Time Tach Learning 1 flash and chirp 2 Times Tach-less Timer Mode 2 flashes and chirps 3 Times (Default) Voltage Sensing 3 flashes and chirps NOTE: BLUE WIRE LOOP INSIDE THE UNIT MUST BE CUT FOR TACH SENSING MODE...
- Page 10 PROGRAMMING - Advanced Operations To Enter Advanced Program Mode: 1. Open the hood and the door. 2. Press & Hold the BRAKE pedal 3. Turn the Ignition Key “On/Off” 4. Press & Release the button on the antenna twice. The system will respond with one siren/horn chirp and light flash to confirm it is in Program Mode and is ready for Feature Programming.
- Page 11 PROGRAMMING - Advanced Program Mode Feature 1 - Passive / Active Arming Press Button 3 Tach Method Confirmation 1 Time Passive Arming 1 flash and chirp 2 Times Passive Arming w/ Lock 2 flashes and chirps 3 Times (Default) Active Arming 3 flashes and chirps Feature 2 - Chirp Delete Press Button 3...
-
Page 12: Relay Diagrams
Blue Vehicle Lock Lock/Unlock To Actuator Switch lock VACUUM - Door locks Fused +12V Green Blue Ground Lock To Vacuum Pump lock POSITIVE TRUNK RELEASE Trunk Release Solenoid Trunk Release Switch Red/White +12V STARTER KILL 2000 SERIES Start Yellow Orange...