Ultra Start 2250 Installation Manual page 6

QUICK START INSTALL QUICK START INSTALL
Step 1 - Connect All Of the Following Wires
6 Pin Power Connector
Yellow Starter Output
Green Heater Output
Red 12 power Input
Red 12 power Input
Blue Ignition 1 Output
White Selectable Output
14 Pin Power Connector
Black System Ground
Pink Brake Switch
White Park Lights
Green/White Hood Switch
Blue/White Tach Input
White/Blue Siren / Horn
Green or(-) Door Input
Purple(+) Door Input
Manual Transmissions Only
Black/White Park Brake
Manual transmission vehicles must have a "M" Series Remote Starter Installed. Manual Transmission Units Must Be Placed Into
Reservation Mode To Operate. See Page 12.
Step 2- Plug-In The Module
When all the connections are done, the control module can be plugged in. Before connecting the control module, make sure the
ignition is in the OFF position. Plug in the 6 pin harness then the 14 pin followed by any other connectors that were used.
Step 3- Auto Tach/Tachless Learn
Tach Learning
1) Make all the required wire connections and plug-in the Unit.
**The park lights should flash twice upon power up.
2) Turn the Ignition Key ON. (The Park Lights will turn on).
3) Start the vehicle with the key, the LED's on antenna will come when proper tach signal is detected. After 30 seconds the park
lights will turn off then flash twice to confirm Tach learning.
* The system will flash the park lights seven times if not Tach/ T achless learned and the start button is pressed. The system must
be Tach/ T achless learned before remote starting.
** If the LED's do not come on during tach learn, a proper Tach signal was not detected.
Note: If the park lights do not flash in auto tach learn mode it may be necessary to connect to a different tach source.
For best results connect the tach to the coil pack or to a fuel injector wire.
Tachless Learning (TL Models Only)
1) Follow Steps 1&2 from above.
2) Start the vehicle with the key, the LED's on antenna will turn on after 30 seconds then park lights will turn off then flash twice to
confirm Tachless learning.
Note: If the first ignition wire is connected to a wire that does not stay 12 volts in the start position the system will not
Tach/ Tachless learn.
Activate Self Learning Impact Sensor
1) Press the LOCK button on the remote 5 times in a row, once every half second. The siren will chirp 3 times and the park lights
will come and stay on solid.
2) While the park lights are on, strike the vehicle at the desired level to trigger the alarm.
3) The siren will respond with one chirp to confirm that the Shock Sensor is programmed. Strike the vehicle 3 times to set the
impact level.
4) Press the lock or unlock button to exit Shock Sensor learning.
Your Basic Install Is Complete!
All manuals and user guides at all-guides.com
Connect The Yellow Wire From The 6 Pin T o The Vehicles Starter Wire.
Connect The Green Wire From The 6 Pin To The Vehicles Accessory Wire.
Connect to Constant 12 Volt Power Source- High Current.
Connect to Constant 12 Volt Power Source- High Current.
Connect The Blue Wire To the Vehicles Primary Ignition Wire.
Select Jumper Position (If Necessary). See Page 5.
Connect The Black Wire To Chassis Ground.
Connect The Pink Wire To The Brake Switch (+) When Brake is Applied.
Connect The White Wire To (+) Park Light System.
Connect The Green/White Wire To The Hood Pin Switch.
Connect The Blue/White Wire To An A/C Tach Source.(Must Be Above 2volts A/C)
Connect The White/Blue Wire To A (+) Siren or To A (+) Horn Wire.
Connect The Green Wire On Vehicles With Negative Door Pin Systems.
Connect The Purple Wire On Vehicle With Positive Door Pin Systems.
Connect (-) Parking Brake
INSTALLATION GUIDE