Technical Data; Angle Grinder Safety Warnings - eisenblatter VARILEX WSF 1800 Original Instructions Manual

TECHNICAL DATA

Rated input ..............................................................................
Output ......................................................................................
Rated speed ............................................................................
Rated speed max ....................................................................
Grinding disk diameter.............................................................
Thread of work spindle ............................................................
Weight according EPTA-Procedure 01/2014 ..........................
Noise/Vibration Information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the
tool are:
Sound pressure level (K = 3 dB(A)) .......................................
Sound power level (K = 3 dB(A)) ............................................
Wear ear protection!
Total vibration values (vector sum in the three axes)
determined according to EN 60745:
Surface grinding: vibration emission value a
Uncertainty K = ........................................................................
For other applications, e.g. Abrasive Cutting-Off Operations
or Wire Brushing other vibration values could occure.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

ANGLE GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Wire Brushing
or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
wire brush, or cut-off tool. Read all safety warnings,
instructions, illustrations and specifi cations provided
with this power tool. Failure to follow all instructions listed
below may result in electric shock, fi re and/or serious injury.
b) Operations such as polishing and sanding are not
recommended to be performed with this powertool.
Operations for which the powertool was not designed may
create a hazard and cause personal injury.
c) Do not use accessories which are not specifi cally
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can break
and fl y apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
f) The arbour size of wheels, fl anges, backing pads or
any other accessory must properly fi t the spindle of the
power tool. Accessories with arbour holes that do not
match the mounting hardware of the power tool will run out
of balance, vibrate excessively and may cause loss of
control.
26 ENGLISH
414 794 - Varilex-WSF1800_16_Sprachen.indd 26 414 794 - Varilex-WSF1800_16_Sprachen.indd 26
ANGLE GRINDER EU (230 V)
............1750 W ................ 1600 W
............1150 W ................ 1050 W
.. 2000-7400 min
............8800 min
125/150/180 mm . 125/150/180 mm
............M 14 ................... M 14
...............2,8 kg ................... 2,8 kg
................90 dB(A) .............. 90 dB(A)
..............101 dB(A) ............ 101 dB(A)
......................... ...............6,3 m/s
h
...............1,5 m/s
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If
power tool or accessory is dropped, inspect for damage
or install an undamaged accessory. After inspecting
and installing an accessory, position yourself and
bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-load
speed for one minute. Damaged accessories will normally
break apart during this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and shop apron capable of stopping
small abrasive or workpiece fragments. The eye
protection must be capable of stopping fl ying debris
generated by various operations. The dust mask or
respirator must be capable of fi ltrating particles generated
by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of workpiece
or of a broken accessory may fl y away and cause injury
beyond immediate area of operation.
j) Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a „live" wire may make
exposed metal parts of the power tool „live" and shock the
operator.
k) Position the cord clear of the spinning accessory. If
you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
GB (110 V)
-1 ... 2000-7400 min -1
............ 8800 min
-1 -1
................ 6,3 m/s
2 2
2 ................ 1,5 m/s 2
05.05.2020 09:16:31 05.05.2020 09:16:31