Advertisement
RSX-G6
QUICK REFERENCE
PROGRAMMING GUIDE (FOR FIRMWARE v1.0)
visit www.OmegaWeblink.com to get the latest firmware
visit www.OmegaDealer.com to download a complete guide
Perform Vehicle Learn
(US patent #10,151,289)
Vehicle Learn is the ultimate time saver and remote start configuration tool. It configures most
install-critical features to match vehicle requirements.
IT'S FASTER THAN PROGRAMMING EVEN ONE FEATURE MANUALLY OR ON YOUR PC!
Vehicle Learn Will:
• Automatically configure IGNITION, ACCESSORY, AND START circuits to match the vehicle.
• Let you quickly choose crank delay (NOTE: wait-to-start via data is always honored)
• Sample crank time for crank averaging (tachless modes only).
• Auto-detect engine running method: Data-tach, tach wire (will also tach learn), or tachless mode.
• Auto-detect data port protocols
Before You Begin:
• Make all wire connections
• Connect any accessories/modules to the data ports.
Make sure any interface module/bypass kit is in "DATA MODE" and programmed to the vehicle.
• If installing on a Manual Transmission vehicle, change feature #6 to desired setup process.
Connect the GREEN wire to the vehicles parking brake and set the parking brake.
Vehicle Learn Procedure:
1.
Turn the ignition key ON (do not start)
2.
Press the valet button 8 times in less than 10 seconds.
- The system will chirp & flash lights to indicate crank delay (Default: 1 chirp/flash = 1.5 seconds).
3.
(OPTIONAL) Press valet to change crank delay.
- Chirp confirmation: 1=1.5 sec, 2=15 sec, 3=20 sec, 4=30 sec.
4.
Start the engine with the key and let the engine reach a normal idle (about 700 rpm).
5.
AUTOMATIC TRANSMISSION: Turn the ignition OFF.
- The system will chirp & flash the lights equal the # of IGN/ACC/START circuits detected (Max: 4).
TIP: If you receive fewer chirps/flashes than circuits you connected, check connections and try again.
MANUAL TRANSMISSION: Release the parking brake (this completes ignition sequence learn.)
- The system will chirp & flash the lights equal the # of IGN/ACC/START circuits detected (Max: 4).
TIP: If you receive fewer chirps/flashes than circuits you connected, check connections and try again.
Set the parking brake again.
Before turning the key OFF, perform the selected MT reservation sequence (feature #6)
- When successful, the LED will once every 2 seconds.
6.
PUSH-BUTTON-START VEHICLES: Exit the vehicle & take the OEM fob/key 20 ft. away to allow remote start.
7.
Activate remote start within 60 seconds of Step 5. Wait until the engine is running and the LED flashes slowly.
- The system will then detect data protocols and the best available engine detection method (datatach, tach, etc.).
- If the brake pedal is pressed before the LED flashes slowly, settings are reset and you must repeat vehicle learn.
8.
TO SAVE SETTINGS & COMPLETE VEHICLE LEARN: Press the BRAKE pedal (the engine will stop).
TO CANCEL/START OVER: Press & release the valet button once.
Programming Features Manually
1.
Turn the ignition key "ON" (do not start).
2.
Press the valet button 5 times within 5 seconds of step 1.
- The horn will chirp 5 times and the Parking Lights will flash 5 times
3.
Press the valet button equal to the desired feature's number.
- The horn will chirp once for every buttomn press.
- Once the desired button presses are complete the horn will chirp to confirm the chossen feature
(long chirp=10 short chirp=1, example: 2 long chirps followed by 5 short chirps equals feature 25).
4.
Press the transmitter button (or brake pedal) to select the desired setting.
- 1-BUTTON MODELS: Change the feature by pressing the transmitter button OR brake pedal the same equal to the
desired setting. Complete all presses before hearing any chirps.
- The siren/horn will chirp equal to the selected setting.
5.
Repeat steps 3 & 4 at this time IF you wish to change additional features.
6.
Turn the ignition key "OFF" to exit programming.
- NOTE: The system will exit automatically at any time after 10 seconds of no activity.
Features Chart
Programmable Features: Ignition on, press valet 5 times (5 chirps/Light flashes)
Lock Button
# Feature
(Brake 1x)
1 Engine Detection
Prog. Voltage
P/W = Ign
2 Pink/White & Gray Output
Gray = Acc
Scan To Download
Green = DBI
3 Data Port Protocol
Black = DBI
the full installation
guide from
4 Remote Start Lock Control
Off
OmegaDealer.com!
5 Crank Delay (Gas/Diesel)
1.5 sec
(login required)
Set w/ remote
6 Manual Trans. Reservation
- Engine Off w/
Lock
7 RS Activation (GREEN wire)
1 Pulse
8 Crank Time
0.75 sec
9 Tachless Low Temp Crank Extend
0 ms
Starter Inter-
10 Yellow/Black Output
rupt
11 Red RS Port Orange/White Wire
Ignition
12 Red RS Port Blue/Orange Wire
Dome Light
13 Orange | Orange/Black Wires
Arm | Disarm
14 Turbo Timer
Off
15 Remote Start Run Time
3 min
16 RS Activation (Remote)
Start x 1
17 Low Temp Auto Start Threshold
0 Deg F
18 High Temp Auto Start Threshold
75 Deg F
19 Remote Valet
Off
20 Brown (Trunk Release) Output
Dome Light
21 Door Lock/Unlock Outputs
0.8 sec
22 Pulse Ign. + Acc. on Disarm
On
23 Alarm Functions |
Alarm On |
1-button Remote Lock/Unlock
Lock+Unlock
Unlock: ON
24 Flashing Light Confirmations
RS: ON
25 Ignition Lock / Unlock
Off
26 Unlock w/ Trunk Release
On
27 Confirmation Chirp Volume
Low
L/U - Horn
28 Confirmation Chirps
RS - 3x honk
29 Horn Trigger Style
Pulse LOW
30 Last Door Arming
Off
31 Automatic Rearming
Off
32 Alarm Trigger Duration
30 sec
33 Arming Delay
3 sec
FEATURE SETTING KEY:
Default Setting
* Door status required from external interface module or DATA sensor w/ analog inputs.
TIP: You can program features via your computer with Omega Weblink.
Visit www.OmegaWeblink.com to learn more.
Features Reset
1. Enter feture programming (DO NOT SELECT ANY FEATURES).
2. Press LOCK + UNLOCK (or press BRAKE x 5)
- 1-button/2-button models: Press the START button 5 times
- You will get5 light flashes to indicate reset & exit programming.
Unlock Button
Trunk Button
Start Button
Lock + Unlock
Trunk + Start
(Brake 2x)
(Brake 3x)
(Brake 4x)
(Brake 5x)
(Brake 6x)
Voltage
Tach Wire
Data-tach
Crank Only
P/W = Acc
P/W = Start
P/W = Ign
P/W = Ign
P/W = Start
Gray = Acc
Gray = Acc
Gray = Ign
Gray = Start
Gray = Start
Green = iData
Green = DBI
Green = iData
Black = iData
Black = iData
Black = DBI
Unlock before
Unlock before
Lock after Start
Lock after RS Off
Start
Start & Lock after
15 sec
20 sec
30 sec
Set w/ remote
Set w/ remote
Set w/ Hand
Off
- Engine Off w/
- Engine Off w/
Brake, Shutdown
Door close
Door close + 10s
upon door close
2 pulses
3 pulses
4 pulses
1 sec
1.5 sec
2.25 sec
3 sec
Average
200 ms
300 ms
400 ms
Starter Interrupt/
Auto-Starter
Anti-grind only
Status
Anti-grind
Interrupt
0.8 sec Defrost
10 min Defrost
Pulse After
Accessory
Horn
Pulse
Pulse
Engine Off
Start
Ignition
Accessory
Status
Light Flash
CH. 4 Latch |
CH. 4 Latch |
Arm | CH. 5
CH. 4 | Disarm
CH. 4 | CH.5
Disarm
CH.5
1 min
2 min
3 min
5 min
10 min
15 min
20 min
30 min
Hold Start
Start x 2
Start x 3
Start x 4
Hold Start 0.8 sec
2sec
15 Deg F
32 Deg F
90 Deg F
105 Deg F
120 Deg F
Lock+Unlock 2 sec
Lock+Unlock 2x
0.8 sec Trunk
2x Press Trunk
2 sec Trunk Button
Button
Button
3 sec
Double Unlock
Total Closure
Off
Alarm Off |
Alarm Off |
Sensor Detect |
Lock+Unlock ON
Unlock Only
Lock+Unlock OFF
Unlock: ON
Unlock: Flash
Unlock: Flash
RS: Flash
RS: ON
RS: Flash
Ign On = Lock
Ign Off = Unlock
Lock + Unlock
Off
Med-Low
Med-High
High
L/U - On Demand
L/U - Horn
L/U - On Demand
Off
RS - 3x honk
RS - None
RS - None
Pulse MED
Pulse HI
Human Panic!
On w/o Lock*
On w/ Lock*
On w/o Lock
On w/ Lock
Enhanced Rearm
60 sec
90 sec
120 sec
15 sec
30 sec
45 sec
Feature 23 (Alarm Functions) must be ON
Tach Wire Signal Learn
When utilizing the tach wire circuit for engine detection, the vehicle's tach signal must be learned. Tach signal is learned
during Vehicle Learn and usually does not have to be relearned. Using either method below will automatically change
Installer Feature #1 to 'Tach Wire'. If a valid tach signal is not detected, the system will not switch to 'Tach Wire' mode.
METHOD 1:
Perform Vehicle Learn - If a tach wire is connected, 'tach wire' mode will be selected and the signal auto-learned.
METHOD 2:
1.
Turn the ignition key "ON".
2.
Press the brake pedal 5 times within 5 seconds of step 1.
- The siren/horn will chirp 5 times.
3.
Start the engine.
- The status LED will turn on when it has learned the tach signal. If not, check tach wire & try again.
4.
Press the valet button to resample the tach signal if needed. If the engine has a high idle at startup, allow the idle to
"settle" around 700 RPM before resampling.
- The status light will flash off then back on when the signal has been resampled.
5.
Turn the ignition key "OFF".
METHOD 3:
6.
Start the engine with the ignition key.
7.
Press & hold the brake pedal.
8.
Press & release the valet button.
- The siren/horn will chirp 5 times.
- The status LED will turn on when it has learned the tach signal. If not, check tach wire & try again.
9.
Turn the ignition key "OFF" or release the brake pedal to exit.
Programming Transmitters
Standard Programming: Use this method to program additional or replacement transmitters.
BEFORE YOU BEGIN: Have all transmitters which are to operate the system at hand.
1.
Turn the ignition key "ON" (do not start).
2.
Press the valet button 4 times within 5 seconds of step 1.
- The horn will chirp 4 times and the Parking Lights will flash 4 times
3.
Press & release the "lock" button on each transmitter one after the other.
- 1-button models, press the "start" button.
- The Parking Lights will flash 1-4 times for each transmitter learned.
- NOTE: When the first new transmitter is learned all previous transmitters are erased.
- NOTE: All other button functions will automatically be assigned.
4.
Turn the ignition key "OFF".
- The horn will sound briefly and the Parking Lights will flash 4 times
- NOTE: The system will exit automatically at any time after 10 seconds of no activity.
Alarm Diagnostics
Alarm Quick Test Mode: Use this mode to test all zones of the alarm system and quickly adjust any sensors.
1.
Press & hold the valet button.
2.
Press the Lock button on the remote within 2 seconds of step 1 (before the system enters valet mode).
- The LED will begin to flash rapidly.
3.
Release the valet button.
- The siren/horn will chirp indicating any alarm zone violations. See the table below.
- NOTE: Chirps will repeat every 2 seconds while the trigger remains violated.
- NOTE: If multiple zones are triggered the chirps will cycle thru the zones every 2 seconds then repeat.
4.
4. Press Lock or Unlock on the controller or power cycle the system to exit.
- NOTE: There is no exit timer to this feature, chirps will continure until the zone is clear or the mode is exited.
Zone Violation Recall: To diagnose alarm triggers, disarm/unlock the alarm with the remote and the status LED will
flash to indicate which zone(s) were triggered last. Turn the ignition key "ON" to clear alarm trigger memory.
LED Flashes/Chirps
Alarm Quick Test
Zone Violation Recall
1
Sensor Full Trigger
-
2
Hood
Hood
3
Door
Door
4
Sensor Warning
Sensor Port Trigger
Remote Start Diagnostics
If remote start fails to activate, the system will flash the parking lights, and flash the status LED to indicate
the cause. If remote start shuts down prematurely after successfully starting, you can recall the violation by putting
the system in valet mode (turn ignition ON and hold the valet button for 5+ seconds). Before the status LED turns on
(system in valet mode), the LED will flash to indicate any violated zones.
LED Flashes
Violated Zone
1
Brake pedal pressed
2
Hood opened
3
System in Valet Mode
4
3D sensor detected vehicle motion while cranking
5
Engine running not detected
6
Received engine stop command (remote, telematics, etc.)
7
MT reservation mode not set
8
Run time expired
9
Low vehicle battery voltage detected
Copyright 2021 Omega Research & Development Technologies, Inc.
QIM_RSX-G6_20210610
Advertisement
