License Rights The purchase of Motorola Solutions products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola Solutions, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.
Supplier's Declaration of Conformity Supplier's Declaration of Conformity Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 2000 Progress Pkwy, Schaumburg, IL. 60196 Phone Number: 1-800-927-2744 Hereby declares that the product: Model Name: L6Q conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a)
RF Energy Exposure and Product Safety Guide for the devices which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. Any modification to this device, not expressly authorized by Motorola Solutions, may void the user's authority to operate this device. Contact Us For inquiries, see https://www.motorolasolutions.com/en_us/support.html...
MN008660A01-AA Read Me First Read Me First Notations Used in This Manual Throughout the text in this publication, you notice the use of Warning, Caution, and Notice. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.
Related Publications Related Publications The following list contains part numbers and titles of related publications. To find and download the publications, visit https://learning.motorolasolutions.com. Part Number Title MN007777A01 Mobile Companion User Guide MN008511A01 Vigilant Hardware Extended Warranty VSD53381 L6Q Inventory Guide...
MN008660A01-AA Document History Document History Version Description Date MN008660A01-AA Initial Release April 2022...
Table 2: L6Q Overview Description Number Description Shroud Camera Mounting Bracket Battery The L6Q is built to be physically secure and to blend in with its surroundings by easily removing and customizing its shroud. Here are some examples of the customization:...
Before heading out to an installation site, complete the steps in the Getting Started section to prepare the L6Q camera ahead of site visits. Review the following list of items and ensure everything needed is on hand before beginning installation.
Installing a SIM Card and SD Card When and where to use: Each L6Q camera requires an activated SIM card to connect to the Internet and upload detections to PlateSearch or Client Portal. A slot for an optional SD card is also provided for additional onboard storage to buffer detections in the event of connection loss.
USB-A power source. NOTE: Notice the location of the QR code above the USB-C port. Later, it is scanned to pair the L6Q Camera to the Mobile Companion application. 3 Unfurl the USB-C Cable and plug it into a USB-A power source.
Prerequisites: To view information about the L6Q camera, log on to the Mobile Companion application using a Vigilant PlateSearch Agency Manager Account or Vigilant Client Portal Site Manager Account. NOTE: If desired, the QR Code Icon at the bottom of the login screen can be used to pair L6Q cameras without logging in.
When and where to use: L6Q cameras must first be paired to the Mobile Companion application in order to send detections to Vigilant PlateSearch, view camera information, and perform aiming. L6Q cameras can be paired either by QR code, NFC (Near Field Communication), or by entering the camera serial number manually.
MN008660A01-AA Chapter 2 : Getting Started Figure 14: End Point Screen 5 Power on the camera by pressing and holding the power button for one second. 6 Pair the camera by performing one of the following methods: Option Actions Pairing by the QR code a Aim the mobile phone camera at the QR code inside of the power port door.
MN008660A01-AA Chapter 2 : Getting Started Option Actions Figure 15: QR Code Location Pairing by NFC Tap the mobile phone to the area inside of the power port door and hold until it scans and the next screen appears.
MN008660A01-AA Chapter 2 : Getting Started Option Actions Figure 16: NFC Pairing Pairing by the serial number a To reveal the camera serial number, re- move the camera shroud. b Enter the <serial number> into the text field and tap Pair Camera when fin- ished.
MN008660A01-AA Chapter 2 : Getting Started Option Actions Figure 17: Serial Number Pairing 7 When the pairing process is complete, tap No, I’m not ready to install. NOTE: This hardware installation process can be resumed later from this screen once at the installation site.
MN008660A01-AA Chapter 2 : Getting Started Figure 18: Pairing Completion Viewing the Camera in Mobile Companion Procedure: 1 Log on to Mobile Companion. 2 To view information about the camera, tap Cameras and from the list, select the camera.
MN008660A01-AA Chapter 2 : Getting Started Figure 20: Cameras Screen 4 Check the Signal Status to verify that the SIM card is active and correctly installed. 5 Check the Battery Level and verify that there is a full charge before installing the camera at the installation site.
1 To pack the camera for transportation to the final installation site, perform one of the following actions: • Place the camera and accessories back into the L6Q Rapid Deployment Carry Case. Proceed to step NOTE: You can minimize trips up and down the ladder during the installation process by using the optional add-on Rapid Deployment Carry Case to safely and securely carry the L6Q kit.
Chapter 3 : Hardware Installation Chapter 3 Hardware Installation L6Q camera systems are developed to be used in location in locations that are utilized by law enforcement, homeowner associations, and local businesses. Installation Site Preparation Sites ideal for the L6Q installation have the following qualities: •...
3.1.1 Assembling the Solar Panel It is recommended to travel with the packaged unit and perform assembly of the solar panel at the L6Q installation site. NOTE: You must perform assembly on the ground before ascending a ladder with the unit.
MN008660A01-AA Chapter 3 : Hardware Installation 9 Secure the Solar Panel Frame to the Mounting Bracket with the Bracket Bolts (2x). AC Power Installation The AC 120V External Power option requires an existing AC power outlet installed by a certified electrician.
MN008660A01-AA Chapter 3 : Hardware Installation Figure 24: Conductors Connection 5 Check the cable length by running the power cable to approximately where the camera will be installed and temporarily secure the cable with a reusable zip tie.
The camera can be mounted to a pole with two included metal band ties or to a flat surface with two included lag bolts. The L6Q kit also includes two reusable zip ties to temporarily hold the mounting bracket in place until the two metal band ties can be secured.
3.5.1 Preparing for Camera Aiming L6Q includes a mobile phone holder to allow for one hand adjustment of the camera. Procedure: 1 Slide the mobile phone into the included mobile phone holder and hook it onto the lower metal band tie.
MN008660A01-AA Chapter 3 : Hardware Installation 3.5.3 Verifying the Successful Capture Prerequisites: Use LEARN Mobile in the Mobile Companion app to verify that L6Q is capturing license plates properly. Procedure: 1 From the Mobile Companion home screen, tap LEARN Mobile.
MN008660A01-AA Chapter 3 : Hardware Installation Figure 27: LEARN Mobile Home Screen 5 Next to CRITERIA, tap the down arrow and select Users. Deselect the All Users checkbox and select the My Scans checkbox. 6 To do a search for all plates, in the Plate Number field, enter the asterisk (*) wildcard character. NOTE: If using a known or test license plate for aiming, enter the license plate number instead.
MN008660A01-AA Chapter 3 : Hardware Installation Figure 28: Search Plate Number License plates scanned by the recently installed camera should appear in the search results. NOTE: Any other license plates scanned under the logged on user will also appear. 7 In the results, tap a license plate and verify that the address information is correct for the recently installed camera.