Renesas SH7085 User Manual
  1. Manuals
  2. Brands
  3. Renesas Manuals
  4. Computer Hardware
  5. SH7085
  6. User manual
Renesas SH7085 User Manual

Renesas SH7085 User Manual

Plqp0144ka-a user system interface board renesas microcomputer development environment system superh family / sh7080 series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
To our customers,
Old Company Name in Catalogs and Other Documents
st
On April 1
, 2010, NEC Electronics Corporation merged with Renesas Technology
Corporation, and Renesas Electronics Corporation took over all the business of both
companies. Therefore, although the old company name remains in this document, it is a valid
Renesas Electronics document. We appreciate your understanding.
Renesas Electronics website:
Issued by: Renesas Electronics Corporation (http://www.renesas.com)
Send any inquiries to http://www.renesas.com/inquiry.
http://www.renesas.com
st
April 1
, 2010
Renesas Electronics Corporation

Advertisement

Table of Contents
loading

Related Manuals for Renesas SH7085

Summary of Contents for Renesas SH7085

  • Page 1 On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding.
  • Page 2 Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific”...
  • Page 3 SH7085 Group PLQP0144KA-A User System Interface Board User’s Manual Renesas Microcomputer Development Environment System SuperH™ Family / SH7080 Series R0E570850CFK00 Rev.4.00 2007.02...
  • Page 5 Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures.

  • Page 7: Important Information

    Improvement Policy: Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as Renesas) pursues a policy of continuing improvement in design, performance, and safety of the emulator product. Renesas reserves the right to change, wholly or partially, the specifications, design, user's manual, and other documentation at any time without notice.
  • Page 8 2. In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this emulator.

  • Page 9: Limited Warranty

    Renesas, upon inspection, shall determine to be defective in material and/or workmanship. The foregoing shall constitute the sole remedy for any breach of Renesas’ warranty. See the Renesas warranty booklet for details on the warranty period. This warranty extends only to you, the original Purchaser.
  • Page 10 3. This user's manual and emulator product are copyrighted and all rights are reserved by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any form, in hard-copy or machine-readable form, by any means available without Renesas’ prior written consent.
  • Page 11 • READ this user's manual before using this emulator product. • KEEP the user's manual handy for future reference. Do not attempt to use the emulator product until you fully understand its mechanism. DEFINITION OF SIGNAL WORDS Either in the user's manual or on the product, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties.
  • Page 12 means WARNING or CAUTION. Example: CAUTION AGAINST AN ELECTRIC SHOCK means PROHIBITION. Example: DISASSEMBLY PROHIBITED means A FORCIBLE ACTION. Example: UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
  • Page 13 Warnings for AC Power Supply: • If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do not plug it forcibly. Failure to comply may cause electric shock and/or fire. • Use an AC power cable which complies with the safety standard of the country.
  • Page 14 • If you smell a strange odor, hear an unusual sound, or see smoke coming from this product, then disconnect power immediately by unplugging the AC power cable from the outlet. Do not use this as it is because of the danger of electric shock and/or fire.
  • Page 15 Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for this emulator. Do not use it for other product. • The DC plug on the included AC adapter has the below polarity.
  • Page 16 Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1. Do not repair or remodel the emulator product by yourself for electric shock prevention and quality assurance.
  • Page 17 Preface The R0E570850CFK00 is a user system interface board that connects a user system for the SH7085 PLQP0144KA-A (former code: FP-144LV) package to the SH7080 E200F emulator (R0E0200F1EMU00 or R0E570800VKK00).

  • Page 19: Table Of Contents

    Section 1 Configuration ...1 Section 2 Environmental Conditions ...3 Section 3 User Interface Specifications ...5 Section 4 Connection Procedures ...9 Connecting User System Interface Board to User System... 9 4.1.1 Installing IC Socket ... 9 4.1.2 Installing Cable Head... 10 4.1.3 Fastening Cable Head ...

  • Page 21: Section 1 Configuration

    PLQP0144KA-A (former code: FP-144LV) package. Please make sure you have all of these components when unpacking. Screws (M2.0 x 6 mm) EV-chip unit Screws (M2.0 x 10 mm) Board Socket cover IC socket User system Figure 1 User System Interface Board for the SH7085 PLQP0144KA-A (Former Code: FP-144LV) Package...
  • Page 22 Use a NQPACK144SD-ND socket (manufactured by Tokyo Eletech Corporation) and a HQPACK144SD (manufactured by Tokyo Eletech Corporation) for the PLQP0144KA-A (former code: FP-144LV) package IC socket and socket cover, respectively, on the user system. Table 1 R0E570850CFK00 Components No. Component Board IC socket Socket cover...

  • Page 23: Section 2 Environmental Conditions

    Section 2 Environmental Conditions Maintain the conditions in table 2 when using the emulator. Table 2 Environmental Conditions Item Temperature Humidity Vibration Ambient gases Specifications Operating: +10 to +35°C Storage: -10 to +35°C Operating: 35 to 80% RH, no condensation Storage: 35 to 80% RH, no condensation Operating: 2.45 m/s max.

  • Page 25: Section 3 User Interface Specifications

    Section 3 User Interface Specifications This user system interface board has the function that masks the chip select signals (CS0 to CS7), bus request signal (BREQ), and wait input signal (WAIT) depending on the setting of a switch. To use the mask function, set switches (SW1 to SW3) on the user system interface board (figure 2), according to tables 3 to 5, and mask pins.
  • Page 26 Table 3 Setting a Switch (SW1) PLQP0144KA-A (Former Code: FP-144LV) Socket Pin No. Table 4 Setting a Switch (SW2) PLQP0144KA-A (Former Code: FP-144LV) Socket Pin No. Signal Name PA6/_CS2/TCLKA PA7/_CS3/TCLKB PA10/_CS0/_POE4 PA11/_CS1/_POE5 PA18/_BREQ/TEND0 PA20/_CS4/_RASU Signal Name PB7/A19/_BREQ/IRQ5/TXD0 PB8/A20/_WAIT/IRQ6/SCK0 PD28/D28/_CS2/TIOC3DS PD29/D29/_CS3/TIOC3BS PA0/_CS4/RXD0 PA1/_CS5/_CE1A/TXD0 Switch...
  • Page 27 Table 5 Setting a Switch (SW3) PLQP0144KA-A (Former Code: FP-144LV) Socket Pin No. Signal Name PA17/_WAIT/DACK2 PA21/_CS5/_CE1A/_CASU/TIC5U PE5/_CS6/_CE1B/TIOC1B/TXD3 PE6/_CS7/TIOC2A/SCK3 Unused Unused Switch Setting Mask canceled Mask enabled Mask canceled Mask enabled Mask canceled Mask enabled Mask canceled Mask enabled...
  • Page 28 Figure 3 shows a circuit for masking signals on the user system interface board. UVCC PA10 PA11 PA18 PA20 PD28 User system PD29 PA17 PA21 Note: The UVcc is the Vcc in the user system. Figure 3 Circuit for Masking Signals PA6_C PA7_C PA10_C...

  • Page 29: Section 4 Connection Procedures

    Section 4 Connection Procedures Connecting User System Interface Board to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE BOARD is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned.

  • Page 30: Installing Cable Head

    4.1.2 Installing Cable Head Check the location of pin 1 before inserting. If the IC socket is not connected properly, the power-supply pins will be shorted as shown below. Align pin 1 on the IC socket for a PLQP0144KA-A (FP-144LV) package on the user system with pin 1 on the user system interface board, and insert the user system interface board into the IC socket on the user system, as shown in figure 4.
  • Page 31 Fasten the user system interface board to the IC socket for a PLQP0144KA-A (FP-144LV) package on the user system with the four screws (M2.0 tightened a little at a time, alternating between screws on opposing corners. Take special care, such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening the screws or twisting the components.

  • Page 32: Connecting User System Interface Board To Ev-Chip Board

    Connecting User System Interface Board to EV-Chip Board Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emulator product or will result in PERSONAL INJURY. The USER PROGRAM will be LOST. 1.
  • Page 33 User system Figure 5 Connecting User System Interface Board to EV-Chip Board EV-chip unit Connector No. EV-Chip Unit Connector No. User I/F Connector 1 (CN4) User I/F Connector 2 (CN5) Board Board Connector No. UCN1 UCN2...

  • Page 34: Recommended Dimensions For User System Mount Pad (Footprint)

    Recommended Dimensions for User System Mount Pad (Footprint) Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a PLQP0144KA-A (former code: FP-144LV) package (NQPACK144SD-ND: manufactured by Tokyo Eletech Corporation). Note that the dimensions in figure 6 are somewhat different from those of the actual chip's mount pad.

  • Page 35: Dimensions For External Bus Trace Unit, Emulation Memory Unit, Ev-Chip Unit, And User System Interface Board

    Dimensions for External Bus Trace Unit, Emulation Memory Unit, EV-Chip Unit, and User System Interface Board The dimensions for the external bus trace unit, emulation memory unit, EV-chip unit, and the user system interface board are shown in figure 7.
  • Page 36 Figure 7 Dimensions for External Bus Trace Unit, Emulation Memory Unit, EV-Chip Unit, 125.0 External bus trace unit 125.0 Emulation memory unit 125.0 EV-chip unit 60.0 30.0 Pin 1 Spacer Unit: mm Tolerance: ±0.5 mm Board and User System Interface Board...

  • Page 37: Resulting Dimensions After Connecting User System Interface Board

    Resulting Dimensions after Connecting User System Interface Board The resulting dimensions, after connecting the user system interface board to the user system, are shown in figures 8, 9, and 10. External bus trace unit EV-chip unit Spacer (φ6.0) Figure 8 Resulting Dimensions after Connecting User System Interface Board (when Connecting External Bus Trace Unit, Emulation Memory Unit, and EV-Chip Unit) Emulation memory unit User system...
  • Page 38 EV-chip unit Spacer (φ6.0) Figure 9 Resulting Dimensions after Connecting User System Interface Board (when Connecting External Bus Trace Unit and EV-Chip Unit) External bus trace unit User system Top view IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Pin 1 Unit: mm Tolerance: ±1.0 mm...
  • Page 39 Spacer (φ6.0) Figure 10 Resulting Dimensions after Connecting User System Interface Board (when EV-chip unit User system Top view Connecting EV-Chip Unit) IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) Pin 1 Unit: mm Tolerance: ±1.0 mm...

  • Page 41: Section 5 Installing The Mcu To The User System

    Section 5 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Philips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw becomes significantly greater than that needed when first tightening.
  • Page 42 Screws (M2.0 x 6 mm) Socket cover MCU (SH7085) Pin 1 IC socket (NQPACK144SD-ND manufactured by Tokyo Eletech Corporation) User system Figure 11 Installing MCU to User System...

  • Page 43: Section 6 Verifying Operation

    Section 6 Verifying Operation 1. Turn on the emulator according to the procedures described in the SH-2A, SH-2 E200F Emulator User's Manual (R0E0200F1EMU00E or R0E570800EMU00E)). 2. The emulator connected to this user system interface board supports three kinds of clock sources as the MCU clock.

  • Page 45: Section 7 Notice

    Before connecting any parts or cables, make sure that pin 1 on the both sides are correctly aligned. Do not apply excessive force to the user system interface board while it is connected to the user system. The dimensions of the recommended mount pad for the IC socket for this user system interface board are different from those of the MCU.
  • Page 47 Publication Date: Rev. 1.00, December 14, 2004 Rev. 4.00, February 26, 2007 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Customer Support Department Global Strategic Communication Div. Renesas Solutions Corp. ©2007. Renesas Technology Corp. All rights reserved. Printed in Japan.
  • Page 48 Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
  • Page 50 SH7085 Group PLQP0144KA-A User System Interface Board User’s Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ10J1205-0400...

Table of Contents