Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PBSS 10-20V
Summary of Contents for Trotec PBSS 10-20V
- Page 1 PBSS 10-20V ORIGINAL INSTRUCTIONS CORDLESS BELT SANDER...
-
Page 2: Table Of Contents
Caution This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. cordless belt sander PBSS 10-20V... -
Page 3: Safety
• Do not expose power tools to rain or wet conditions. safety principles. A careless action can cause severe Water entering a power tool will increase the risk of injury within a fraction of a second. electric shock. cordless belt sander PBSS 10-20V... - Page 4 • Use power tools only with specifically designed battery packs. Use of any other battery packs may create a risk of injury and fire. cordless belt sander PBSS 10-20V...
- Page 5 The spinning accessory may grab the surface and pull the power tool out of your control. • Secure the workpiece. The grip of tensioning devices or a vice is more secure than holding the workpiece only by hand. cordless belt sander PBSS 10-20V...
- Page 6 The following safety signs and labels are attached to the charger: The device must only be used for dry sanding. We recommend using the power tool with original Trotec This symbol indicates the following: accessories. Read the instructions or operating manual before charging the battery.
- Page 7 Burn hazard when touching the insertion battery off the device as described in chapter "Removing tool. the battery". Do not touch the insertion tool bare-handed! 3. Do not insert the battery if the device is defective. Wear protective gloves! cordless belt sander PBSS 10-20V...
-
Page 8: Information About The Device
The battery comes with its own battery level indication. As a result you can check the current charging status without having to connect it to the device. Device depiction cordless belt sander PBSS 10-20V... - Page 9 Vibration emission value front 3.03 m/s² handle a Uncertainty K 1.5 m/s² Sound values according to EN 62841-2-4 Sound pressure level L 80 dB(A) Sound power L 91 dB(A) Uncertainty K 3 dB Wear hearing protection. Excessive noise can lead to hearing loss. cordless belt sander PBSS 10-20V...
-
Page 10: Transport And Storage
– Only ship batteries if their housing is undamaged. – Mask open terminals with tape and pack the battery in a way that it cannot move inside the packaging. – Please also observe any other national regulations. cordless belt sander PBSS 10-20V... -
Page 11: Start-Up
Allow the battery (6) to cool down to room temperature. national regulations. 5. Take the battery (6) out of the quick charger (7) by pressing and holding the release button (14) and pulling the battery (6) off the quick charger (7). cordless belt sander PBSS 10-20V... - Page 12 It might be necessary to adjust the speed of rotation / belt speed according to the new abrasive belt. 2. If required, charge the battery (6) as described in the section Charging the battery. cordless belt sander PBSS 10-20V...
- Page 13 2. Remove the old abrasive belt (10) from the device. 4. Close the locking lever (17). 5. Switch the device on. Upon switch-on the belt run is automatically centred. If not, the belt run may have to be adjusted manually using the adjusting screw (15). cordless belt sander PBSS 10-20V...
- Page 14 3. Empty the dust bag (9) in due time to maintain an optimum absorption of dust. ð If the belt run is still not centred after the adjustment, the abrasive belt (10) needs to be replaced. cordless belt sander PBSS 10-20V...
- Page 15 If required, you can connect the adapter for dust extraction (11) to the dust extraction connection (5) first. If anything is unclear or if you have questions, please contact the manufacturer of your vacuum cleaner. cordless belt sander PBSS 10-20V...
-
Page 16: Operation
(3 – 4) for dry sanding untreated wooden surfaces. • Use a dust extraction system when grinding off residual paint. Paint residues might smelt and then smudge both workpiece and abrasive belt. cordless belt sander PBSS 10-20V... - Page 17 4. Position the device on the workpiece. 5. Lift the device off the workpiece before you switch it off. 6. Press the on/off switch (18) to stop continuous operation. ð The locking switch (2) automatically returns to its initial position. cordless belt sander PBSS 10-20V...
-
Page 18: Available Accessories
Only use accessories and additional equipment • Check the quick charger for damages. Should the quick specified in the instructions. charger be damaged, stop using it. Contact the Trotec Using insertion tools or accessories other than those customer service. specified in the instructions may cause a risk of injury. -
Page 19: Maintenance
Safety signs on the battery and the charger Check the safety signs attached to the battery and the charger at regular intervals. Replace illegible safety signs! cordless belt sander PBSS 10-20V... -
Page 20: Disposal
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life. - Page 21 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...