Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec EdgeProtect 4550
Summary of Contents for Trotec EdgeProtect 4550
- Page 1 PMSS 10-200 OPERATING MANUAL 3-IN-1 MULTI-FUNCTION SANDER...
-
Page 2: Table Of Contents
This symbol indicates dangers to the health of persons due to hand injuries. Warning This signal word indicates a hazard with an average https://hub.trotec.com/?id=41419 risk level which, if not avoided, can result in serious injury or death. Caution This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. -
Page 3: Safety
General Power Tool Safety Warnings – Electrical Safety safety Read this manual carefully before starting or using the • Power tool or power adapter plugs must match the device. Always store the manual in the immediate vicinity outlet. Never modify the plug in any way. Do not use of the device or its site of use! any adapter plugs with earthed (grounded) power Warning... - Page 4 • Remove any adjusting key or wrench before turning General Power Tool Safety Warnings – Service the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal • Have your power tool serviced by a qualified repair injury.
- Page 5 The device must only be used for dry sanding. • During operation hold onto the power tool with both We recommend using the power tool with original Trotec hands. Make sure that you stand firmly on the ground. It is accessories.
- Page 6 Personnel qualifications Warning of explosive substances Fine dust produced during grinding is highly People who use this device must: flammable. Risk of fire and explosion! • have read and understood the operating manual, especially Use a dust or chip bag or a dust extraction system for the Safety chapter.
-
Page 7: Information About The Device
Warning Information about the device Risk of suffocation! Do not leave the packaging lying around. Children may Device description use it as a dangerous toy. The device PMSS 10-200 is a 3-in-1 multi-function sander for dry sanding. Caution The device is equipped with a 200 W motor. Vibration emissions can cause a health hazard if the device is used for an extended period of time or if it is The three sanding plates delta sander, random orbital sander... - Page 8 Device depiction Designation On/off switch Dust extraction connection Random orbital sanding plate Clamping bracket Locking lever Orbital sanding plate Reducer Sanding sheet Screw Rubber pin Dust collector with filter Dust box release button Delta sanding plate Setting wheel for oscillation rate selection Scope of delivery •...
-
Page 9: Technical Data
Technical data Information on noise and vibration: • The vibration level specified in these instructions was Parameter Value determined by means of a measuring method standardized in EN 60745 and can be used for a device comparison. The Model PMSS 10-200 specified vibration emission value may also be used for a Mains connection 1/N/PE ~ 230 V / 50 Hz preliminary assessment of the exposure. -
Page 10: Transport And Storage
Transport and storage Start-up Unpacking the device Notice • Take the transport case out of the packaging. If you store or transport the device improperly, the device may be damaged. Warning of electrical voltage Note the information regarding transport and storage of Electric shock from insufficient insulation. - Page 11 ü Use tools suitable for the intended task. 4. Check the felt ring (21) for correct fit. 1. Loosen the four screws (9) at the sanding plate (3). ð The sanding plate is now loosened. 2. Remove the sanding plate (3) from the device. 5.
- Page 12 8. Press the sanding plate onto the flange (16) until it clicks Changing the sanding sheet into place. Warning of electrical voltage 9. Tighten the four screws (9). Before any work on the device, remove the mains plug from the mains socket! Hold onto the mains plug while pulling the power cable out of the mains socket.
- Page 13 4. To exchange or remove the sanding sheet, simply pull it off 3. Fold the locking lever (5) back up to close the clamping the sanding plate. bracket (4). Fix the locking lever at the orbital sanding plate again. When using the orbital sanding plate, you can also use sanding ð...
- Page 14 Assembling the dust collector Mounting the external dust extraction system Alternatively, you can also connect the dust extraction system to Warning of explosive substances the device. Wood dust inside the dust collector can self-ignite in case of flying sparks. Do not use the dust extraction Warning of explosive substances system when grinding metals! Wood dust inside the dust collector can self-ignite in...
-
Page 15: Operation
Oscillation rate selection Operation By use of the setting wheel for oscillation rate selection you can Tips and notes on handling the multi-function sander change the oscillation rate at any time, even during operation of General information: the device. The required oscillation rate depends on the material •... - Page 16 The non-binding values listed in the table below shall serve as a 4. To switch the device off, slide the on/off switch (1) to 0. point of reference for selecting the right sanding sheet for the task at hand: For processing paint and lacquer grain size: 40 –...
-
Page 17: Errors And Faults
The device becomes hot: company or by Trotec. • Make sure not to exert too much pressure on the device Slight smoke or odour are emitted during first use: during operation. -
Page 18: Maintenance
Warning of electrical voltage Maintenance tasks which require the housing to be opened must only be carried out by authorised specialist companies or by Trotec. Notes on maintenance Inside the device, there are no parts that need to be maintained or lubricated by the user. -
Page 19: Disposal
Cleaning / changing the filter insert of the dust collector Disposal The filter insert has to be cleaned as soon as it is dirty. Check the filter insert for dirt once or twice a year. The filter insert should be exchanged in case of heavy soiling or The icon with the crossed-out waste bin on waste damage. - Page 20 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...