Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PBSS 10-600
Summary of Contents for Trotec PBSS 10-600
- Page 1 PBSS 10-600 ORIGINAL INSTRUCTIONS BELT SANDER...
-
Page 2: Table Of Contents
Caution This signal word indicates a hazard with a low risk level which, if not avoided, can result in minor or moderate injury. belt sander PBSS 10-600... -
Page 3: Safety
• Do not force the power tool. Use the correct power tool suitable for outdoor use reduces the risk of electric shock. for your application. The correct power tool will do the job better and safer at the rate for which it was designed. belt sander PBSS 10-600... - Page 4 • Do not run the power tool while carrying it at your Just because the accessory can be attached to your power side. Accidental contact with the spinning accessory could tool, it does not assure safe operation. snag your clothing, pulling the accessory into your body. belt sander PBSS 10-600...
- Page 5 • Do not operate the power tool near flammable The device must only be used for dry sanding. materials. Sparks could ignite these materials. We recommend using the power tool with original Trotec • Only use the power tool for dry sanding. Water entering accessories.
- Page 6 The insertion tool might still be hot after the cable out of the mains socket. application. Burn hazard when touching the insertion 3. Do not reconnect a defective device to the mains. tool. Do not touch the insertion tool bare-handed! Wear protective gloves! belt sander PBSS 10-600...
-
Page 7: Information About The Device
• 1 x Device PBSS 10-600 • 1 x Adapter for external dust extraction • 1 x Dust collector • 1 x Reducer • 2 x Retaining bracket • 1 x Abrasive belt for wood, grain size: 80, dimensions: 75 x 457 mm • 1 x Manual belt sander PBSS 10-600... - Page 8 Uncertainty K 1.5 m/s² Sound values according to EN 60745 Sound pressure level L 86.83 dB(A) Sound power L 97.83 dB(A) Uncertainty K 3 dB Wear hearing protection. Excessive noise can lead to hearing loss. belt sander PBSS 10-600...
-
Page 9: Transport And Storage
The abrasive belt can be exchanged for processing different materials. Moreover available are different grain sizes for coarse to fine sanding. It might be necessary to adjust the speed of rotation / belt speed according to the new abrasive belt. belt sander PBSS 10-600... - Page 10 2. Remove the old abrasive belt (7) from the device. 4. Close the locking lever (11). 5. Switch the device on. Upon switch-on the belt run is automatically centred. If not, the belt run may have to be adjusted manually using the adjusting screw (10). belt sander PBSS 10-600...
- Page 11 Avoid overheating of the workpiece and the device. Empty the dust collector or the vacuum cleaner's dust collection bag at regular intervals. Wear a protective mask Wear an appropriate protective mask when working with the device. belt sander PBSS 10-600...
- Page 12 If anything is unclear or if you have questions, please contact the manufacturer of your vacuum cleaner. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. belt sander PBSS 10-600...
-
Page 13: Operation
(3 – 4) for dry sanding untreated wooden surfaces. • Use a dust extraction system when grinding off residual paint. Paint residues might smelt and then smudge both workpiece and abrasive belt. belt sander PBSS 10-600... - Page 14 ð The on/off switch is locked in place. ð The device keeps running and continuous operation is activated. 4. Position the device on the workpiece. 5. Lift the device off the workpiece before you switch it off. belt sander PBSS 10-600...
-
Page 15: Errors And Faults
Remove the blockages, if any. • Check whether you are using an abrasive belt that is suitable for this device. 4. Check the retaining brackets (9) for tight fit. 5. For the disassembly unscrew the retaining brackets (9) counter-clockwise. belt sander PBSS 10-600... -
Page 16: Maintenance
• Check the belt speed setting. It must be suitable for both opened must only be carried out by authorised the abrasive belt and the material. specialist companies or by Trotec. • Select a higher speed level by turning the setting wheel for the belt speed selection to the desired level. -
Page 17: Disposal
3. Empty the dust collector completely. Use a brush to remove adherent abrasive dust. 4. Push the dust collector (6) back onto the adapter connection (4). The dust collector (6) must click into place at the device. belt sander PBSS 10-600... -
Page 18: Declaration Of Conformity
Declaration of conformity In accordance with the EC Machinery Directive 2006/42/EC, Annex II, part 1, Section A Herewith, we – Trotec GmbH & Co. KG – declare that the machinery designated below was developed, constructed and produced in compliance with the requirements of the EC Machinery Directive in the version 2006/42/EC. - Page 20 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...