Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ZKTeco AL30 Series
Summary of Contents for ZKTeco AL30 Series
- Page 1 Installation Guide AL30 & AL40 Series Smart Lock Version: 2.0 Date: December 2019...
- Page 2 On every installation, you must perform the initialization process just after the installation of this lock on any door as described in Initialization Procedure on page 7. v Do not insert the batteries before installing the lock! Need Help? For technical documents and more Please visit www.zkteco.com/en Email: online@zkteco.com...
-
Page 3: Table Of Contents
Contents What’s in the box.........................1 Installation Diagram(AL30B)......................1 Installation Procedure.........................2 1. Setting up the door..............................2 2. Adjust the backset of the lock to 70mm (if needed)..................3 3. Latch Installation..............................3 4. Installation of Outdoor assembly........................4 5.Installation of Mounting plate with Gasket....................5 6. Installation of Indoor assembly...........................6 7. -
Page 4: What's In The Box
What’s in the box Mounting Outdoor Indoor Gasket plate assembly assembly Strike Latch Strike Keys Screw B plate Screw A Note: Please use the appropriate set of C screws as per your door's thickness, to assure the proper functioning of the locks. 3M tapes Stud Screw length... -
Page 5: Installation Procedure
Installation Procedure 1. Setting up the door 1) Tape the Installation Template at the desired handle height. 2) Mark for the holes and drill the marked location. 3) The hole A doesn’t need to be drilled if the lock will be fixed by 3M Tapes. Important Notice It is not required to drill hole on the door. -
Page 6: Adjust The Backset Of The Lock To 70Mm (If Needed)
2. Adjust the backset of the lock to 70mm (if needed) Backset is the distance from the edge of the door to the center of the hole drilled on the door. The default Backset is 60mm, but if you want to change the Backset to 70mm, grasp body and twist the Faceplate as shown below: Press the Bolt inside the Latch Rotate the Faceplate... -
Page 7: Installation Of Outdoor Assembly
4. Installation of Outdoor assembly There are two methods to install the Outdoor assembly. v Method 1: Installing with 3M Tapes Paste a 3M Tape on the Mounting 1) Make sure the highlighted Spindle is in the horizontal plate of Outdoor assembly. position, as shown. -
Page 8: Installation Of Mounting Plate With Gasket
5. Installation of Mounting plate with Gasket v Method 1: Installing with 3M Tapes 1) Paste a 3M Tape on the Mounting plate of Indoor assembly. 2) Attach the Mounting plate to the Gasket and route the cable through the hole on the Mounting plate and Gasket. -
Page 9: Installation Of Indoor Assembly
6. Installation of Indoor assembly Connect the male cable to the female Place the Indoor assembly properly on the connector on the Indoor assembly. Mounting plate. Then use A screws to secure Indoor assembly. The Knob dot must be positioned in direction of Bolt. 7. -
Page 10: Initialization Of Lock
8. Initialization of Lock After installing the Lock, you must perform Initialization process, as explained in the steps below: extended 1) Rotate the Knob to make the Latch Bolt in the position. 2) First, insert just 3 batteries in the Lock. 3) Use a needle or a pin to press hold... -
Page 11: Mark And Drill Holes For The Strike Box And Plate
9.Mark and drill holes for the Strike box and Plate Make sure that the Strike box is in the level Align the Strike box and Plate with the drilled of Latch Bolt, then use Installation Template hole and use B screws to secure them. to drill holes. -
Page 12: Fcc Warning
Warning: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.