Download
Share
Print this page
ICS 814 PRO Operator's Manual
  1. Manuals
  2. Brands
  3. ICS Manuals
  4. Saw
  5. SpeedHook 814PRO
  6. Operator's manual

ICS 814 PRO Operator's Manual

Hydraulic saw
Hide thumbs Also See for 814 PRO:

Advertisement

Quick Links

Download this manual
814PRO Hydraulic Saw
OPERATOR'S MANUAL
© 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595

Advertisement

loading
Need help?

Need help?

Do you have a question about the 814 PRO and is the answer not in the manual?

Questions and answers

Related Manuals for ICS 814 PRO

Summary of Contents for ICS 814 PRO

  • Page 1 814PRO Hydraulic Saw OPERATOR’S MANUAL © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 3: Table Of Contents

    To get the maximum benefit from your saw, and ensure maximum safety, be sure to read this manual thoroughly, and periodically review safety instructions. SYMBOLS & LABELS SAFETY TECHNICAL SPECIFICATIONS SET-UP OPERATION MAINTENANCE TROUBLESHOOTING REFERENCE © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 4: Symbols & Labels

    READ OPERATIONS & MAINTENANCE MANUAL BEFORE USE OF TOOL. FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS PERSONAL INJURY © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...
  • Page 5 DO NOT use your hands to search for hydraulic leaks. Hydraulic fluid escaping under pressure can penetrate skin. If any hydraulic flud is injected into skin seek medical attention immediately. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 6: Safety

    Provide adequate ventilation when working in an enclosed area. Breathing exhaust gases is dangerous. • To avoid electrocution, check for live electrical wiring near cutting area. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 7: Technical Specifications

    (1)Output ratings based on typical input conditions and efficiency assumptions and may vary depending on power supply. (2)Measured in accordance with ISO3744:2010, ISO15744:2002 and ISO11203:1995 (3)Measured in accordance with ISO5349-1:2001 and 1SO5349-2:2001 © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 8: Set-Up

    Turn the chain-tensioning screw CCW until the bar comes into inside the bar groove, then pre- contact with the drive sprocket. tension the chain. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...
  • Page 9 The diamond chain should be snug but be able to be pulled around the guide bar by hand. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 10: Operation

    = 12 in x 12 in x12 in = 150 lbs (30 cm x 30 cm x 30 cm = 68 kg). • Check for live electrical wiring near the cutting area or in the concrete to avoid electrocution. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...
  • Page 11 When using a new diamond chain, you can increase the cutting speed by opening up the diamonds by making a few cuts in an abrasive material such as a cinder block. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 12: Maintenance

    After cleaning the saw, spray the entire saw body, diamond chain, guide bar, and drive sprocket with lightweight oil. Using lightweight oil on the saw will minimize rust and help reduce slurry build up. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...
  • Page 13 2–3 diamond chains. 1. Retaining Ring 2. Washer 3. Rim Sprocket 4. Splined Sprocket Adaptor Note: Rim sprocket may be installed with either side facing outwards. © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 14: Troubleshooting

    MOTOR WON'T TURN – Hydraulics are hooked up backwards or powerpack is set on reverse • flow. Further questions? Call 800.321.1240 visit our website at: icsdiamondtools.com © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...
  • Page 15 2. Determine the length of the cut in feet. 3+7+3+7=20 feet 3. Multiply the two numbers 8 in x 20 ft = 160 in-ft © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...

  • Page 16: Reference

    ASSUMPTIONS: • 8 gpm (30 lpm) flow at 2,500 psi (172.5 bar) • Zero elevation change • 2 pairs of flush-face fittings per hose © 2022 ICS, Oregon Tool Inc. Specifications are subject to change without notice. REV071918~ F/N 74595...
  • Page 18 814PRO OPERATOR'S MANUAL ICS, Oregon Tool Inc. 4909 SE International Way Portland, OR 97222 Tel 800.321.1240 icsdiamondtools.com © 2018 ICS, Blount International Inc. Specifications are subject to change without notice. REV071918 F/N 74595...