Page 1
GLOBAL STATUS LOCAL STATUS System Reset Beacon Test Global Ticktone Global Sense Test Matrix HMI Amplifier Beacon I/O Power Default System Global Bus Power Aux I/P PABX Routine Important Alarms Beacons Sonix 2mx Dist Config Switchover Data Sync Speech Message...
Page 2
CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other-wise for any special, indirect, incidental or consequential damage or loss whatsoever, including but not limited to...
Page 3
A 2Mx bus, used to communicate with SAS application Sync A 2Mx bus used to communicate with the second 2Mx unit when PA/GA system is confi gured as A&B, AB+ or N+1 system SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Tick-tone feature for testing and commissioning • purposes Beacon test feature for testing and commissioning • purposes Provides simple user indication on system status • Comprehensive alarm tone library (custom tones • available on request) SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
As these cables are power feeds they should be routed within the PA/GA system in a way as to avoid contact with other signal, audio or high voltage cables. SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Indication Top port Left Receive Right Transmit active Bottom Port Left Receive Right Transmit active (only active in split loop scenarios) Table 4 - 2Mx Rear Bus Port indicators SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Figure 4 - Example Bus data fl ow Unit #N Unit #N Unit #2 5.4.2.1 Split loop If the data bus is broken, then the Sonix 2Mx 2Mx Unit Figure 7 - Active audio routing automatically enters ‘split loop’ mode and transmits Unit #N...
Table 11 - Remote system activity indicator states Pattern State BGM not available / configured Slow flashing BGM is available but not active Solid BGM is active on the system Table 7 - BGM Indicator states SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
BUT primary controller is is detected detected Table 16 - N+1 indicator states The N+1 indicators are only active when the 2Mx controller has ote: been configured in N+1 mode. SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
When a ping set request (unit ID change request) for a 2Mx is received by the unit, it flashes all 4 action indicators near the pushbutton for 10 seconds to SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Beacon controllers. A Side B Side 2Mx Central Controller 2Mx Central Controller 350-d Amplifier 350-d Amplifier Access Panel 350-d Amplifier 350-d Amplifier Access Panel 350-d Amplifier 350-d Amplifier SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com Access Panel...
+48 V Con g Primary 2Mx Beacon Bus Ampli er Bus Bottom Bottom Primary 2Mx Primary 2Mx Bottom Bottom High Speed Low Speed +48 V Bottom Bottom Secondary 2Mx Secondary 2Mx SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Con g Primary 2Mx Secondary 2Mx Fault Default +48 V Con g Primary 2Mx Beacon Bus Ampli er Bus Bottom Bottom SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com Primary 2Mx Primary 2Mx Bottom Bottom High Speed Low Speed...
Priority for each unit must be unique within each system but A ote: and B sides of unit should be the same. bus is 100m (please discuss with your local Eaton representative on longer distances) SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Activation of global fault signal via the Io • ote: Eaton recommend an Alarm Attenuate setting of 120 with a mini- Visual indication of fault source and type on 2Mx front • mum value of 30 and a maximum value of 245 panel See SAS manual for more information.
8.7 Health monitoring 8.9 Access panel timeout The Sonix 2Mx comes with a set of health monitoring tools as standard. Access panel timeout is used to prevent a single access panel from utilising the system without break.
The program fault, or minor fault, is a signal generated from a sub-set of the available system faults and transmitted out of the PA/GA system via the Sonix Io unit. The list of standard faults available is as follows: SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Figure 19 - 2Mx fault tree ote: The Sonix 2Mx unit itself does not contain any history of faults logged, these are included as part of a permanent SAS installation. See the SAS software for a list of faults for specifi c equipment type.
• field cabling etc., isolating cabling can cause faults to be detected ote: Missing unit faults can occur during configuration if a unique ID is changed (see section 8.7 .2). SONIX 2MX TECHNICAL MANUAL TM370 / A June 2022 www.eaton.com...
Page 26
All specifications, dimensions, weights and tolerances are nominal (typical) T: +44 (0) 1623 444 400 Publication www.crouse-hinds.com/hac No.TM370 / A and Eaton reserve the right to vary all data without prior notice. No liability is accepted for any consequence of use. MEDCSales@Eaton.com June 2022...