Related Manuals for VWR Advanced Mini Block Heaters
Summary of Contents for VWR Advanced Mini Block Heaters
- Page 1 Instruction Manual Advanced Mini Block Heaters Advanced Mini Block Heater with Heated Lid...
-
Page 2: Package Contents
able of ontents Package Contents ....Warranty ....Installation ....Maintenance &... -
Page 3: Installation
The VWR Mini Block Heaters are intended for general laboratory use. Safety can not Upon receiving the VWR Mini Block Heater, check to ensure that no damage has occurred in shipment. It is important that any damage that occurred in transport is be guaranteed if used outside of the intended use. -
Page 4: Safety Instructions
& r afety nstrUctions tandards egUlations Please read the entire instruction manual before operating the Dry Block Heater. Henry Troemner, LLC hereby declares under its sole responsibility that the construction of this product conforms in accordance with the following standards: WARNING! DO NOT use the Mini Block Heater in a hazardous atmosphere or with hazardous materials for which the unit was not designed. -
Page 5: Instructions De Sécurité
nstrUctions de sécUrité orMes et régleMentations Veuillez lire le manuel d’utilisation dans sa totalité avant de faire fonctionner le bain à sec Le fabricant déclare par la présente, sous sa seule responsabilité, que la construction chauffant. de ce produit est conforme aux normes suivantes: ATTENTION ! Ne pas se servir du bain à... - Page 6 & M dvanced lock eater lock eater WitH eated Pecifications Overall dimensions (L x W x H): 6.3 x 5 x 4.85” (16 x 12.7 x 12.3cm) Electrical (50/60 Hz): Non Heated Lid: 120 volts: 0.440 amps, 49 watts 230 volts: 0.250 amps, 48 watts Heated Lid: 120 volts:...
- Page 7 dvanced lock eater ontrol anel C. Temperature display: Displays the actual temperature and will beep when the The front panel of the Mini Block Heater contains all the controls and displays needed to operate the unit. set-point temperature is reached. D. Up/down arrows for set-point control. On/off button starts/stops the heating function.
-
Page 8: Perating I Nstructions
Perating nstrUctions Designed for applications that require repeatable results and superior temperature c. To stop heating, press the on/off button under the temperature display. stability. These multi-purpose units are ideal for incubation and activation of cultures, d. Allow time for the temperature to stabilize. The actual temperature displayed enzyme reactions, immunoassays, melting/boiling points, and a wide variety of other is the temperature at the bottom of the modular block. -
Page 9: Calibration Procedure
’ Perating nstrUctions CALIBRATION PROCEDURE TEMPERATURE TESTING This procedure is used to fine tune and calibrate the block temperature at a specific 1. To ensure good thermal conductivity, select the proper Modular Heating Block for temperature setting. This process may be repeated for up to three (3) separate set- your application. - Page 10 ’ Perating nstrUctions STABILITY TESTING 2. The recommended procedure for testing the unit’s temperature uniformity is as follows: 1. The manufacturer has performed temperature stability tests on Mini Block Heaters. a. Set-up the unit in a stable environment. The manufacturer used calibrated temperature measuring devic for the stability b.
- Page 11 MINI MODULAR HEATING BLOCKS AND SAMPLES To enter the Function Modes, perform the following steps: Only VWR Mini Modular Heating Blocks are to be used in the Mini Block Heaters. 1. Place unit in standby mode. 1. Select the proper blocks that will be a precise fit for the tubes that you will be using 2.
-
Page 12: Troubleshooting
Please contact your VWR representative for repair. If using probe, verify probe is in thermo well and follow Single Point Calibration Unit cannot reach set-point or instructions on page 10. If problem persists, please contact your VWR representative Probe not in thermometer well for repair. - Page 13 lock eater ePlaceMent arts escriPtion UMber 1. RTD - Heater plate assembly 349255-00 2. Main heater 349263-00 3. Heater insulation 249020-00 4. Clear lid 249652-00 5. Disk thermostat 380235-00 6. Tool handle 849600-00 7. Power entry module 386122-00 8. Top housing 249651-00 9.
- Page 14 lock eater WitH eated ePlaceMent arts escriPtion UMber 1. Clear lid 249652-00 2. Screws (for lid heater top plate) 130283-00 3. Lid heater top plate 249654-00 4. Heater insulation 249020-00 5. Lid heater 349264-00 6. Lid heater bottom plate 249655-00 7.
- Page 16 anufactured by TROEMNER LLC 201 Wolf Drive Thorofare, NJ 08086-0087 Phone: 856-686-1600 • Fax: 856-686-1601 • E-mail: troemner@troemner.com www.troemner.com 549500-00 (REV 2 - 07/16)