Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for VWR Standard Series
Summary of Contents for VWR Standard Series
- Page 1 Instruction Manual Standard Orbital Shaker Advanced Orbital Shaker...
- Page 2 (5) years. Register your equipment or 92” (234cm) detachable power cord instrument online at www.vwr.com/warranty for US residents or www.vwrcanlab.com/ Instruction manual warranty for Canadian residents. For your reference, make a note of the serial num- ber, date of purchase and supplier here.
- Page 3 Upon receiving the VWR Orbital or Reciprocating Shaker, check to ensure that no These Shakers are intended for general laboratory use. damage has occurred during shipment. It is important that any damage that occurred Operating Conditions: Indoor use only.
- Page 4 nvironMental onditions tandard qUiPMent isPosal *For use in CO2 environments, incubators, or cold rooms. This equipment must not be disposed of with unsorted waste. It is your responsibility to Temperature: 0 to 40°C (32 to 104°F) correctly dispose of the equipment at life-cycle-end by handing it over Humidity: maximum 80% relative humidity, non-condensing to an authorized facility for separate collection and recycling.
- Page 5 Please read the entire instruction manual before operating the Orbital Shaker. VWR hereby declares under its sole responsibility that the construction of this product conforms in accordance with the following standards: WARNING! DO NOT use the Orbital Shaker in a hazardous atmosphere or with hazardous materials for which the unit was not designed.
- Page 6 orMes et régleMentations onsignes de sécUrité S’il vous plaît lire l’intégralité du manuel d’instructions avant de faire fonctionner l’agitateur Troemner, LLC déclare par la présente sous sa seule responsabilité que la conception orbital. de ce produit répond aux exigences des normes suivantes: AVERTISSEMENT! N’UTILISEZ PAS utiliser le secoueur orbital dans un Normes de sécurité: milie u dangereux ou en présence de matières dangereuses non conformes...
- Page 7 Pecifications MODEL 1000 MODEL 3750 Overall dimensions LxWxH 11 x 17 x 4” (27.9 x 43.2 x 10.2cm) Overall dimensions LxWxH 16.25 x 14 x 5.75” (41.3 x 35.6 x 14.6 cm) Tray dimensions LxW 8.75 x 11.75” (22.2 x 29.8) Tray dimensions LxW 13 x 11”...
- Page 8 ’ Pecifications cont tandard rbital haker MODEL 10000 *With optional platform and flask clamp Overall dimensions LxWxH 28.25 x 26.7 x 7.0” (71.8 x 67.8 x 17.8 cm) Tray dimensions LxW 24 x 24” (70 x 70cm) Electrical 120 volts: 5 amps, 80 watts 230 volts: 2.5 amps, 80 watts...
- Page 9 tandard rbital haker Perating nstrUctions The Standard Orbital Shaker is used for general laboratory shaking needs. 2. Setting speed: a. To run in continuous mode, push rocker to the run position. Set speed knob to MODEL 1000 desired setting and adjust if necessary. Unit will run until you move the rocker 1.
- Page 10 ontrol anel dvanced rbital haker The front panel of the Advanced Orbital Shaker contains all the controls and displays D. Time display: Displays accumulated time (continuous mode) or how much time is needed to operate the unit. remaining (timed mode). The display range is from 0 to 9,999 minutes in one (1) second increments.
- Page 11 dvanced rbital haker Perating nstrUctions The Advanced Orbital Shaker has been designed for the speed and time functions b. Simultaneously press both the up and the down arrows, the display will indicate to work independently of one another. The speed can be re-set without re-setting zero (0:00).
- Page 12 ’ Perating nstrUctions cont 5. Turning unit off: ADDITIONAL LOAD SENSING FEATURE a. To turn the unit off, press the standby button. The speed and time displays will The Advanced Orbital Shaker Models 3750 and up, are equipped with an additional be blank, the standby indicator light will illuminate.
- Page 13 Cause Solution Mechanical obstruction Unit will not run Add or replace fuse as necessary. If problem persists, please contact your VWR representative for repair. Motor obstruction Sensor fan misaligned Unit is excessively noisy Ensure that tray is secured tightly. If problem persists, please contact your VWR representative for repair.
- Page 14 1000 ePlaceMent arts tandard DESCRIPTION PART NUMBER Rubber Mat 480016-00 Tray (STD) 280760-00 Tray (ADV) 580050-00 Top Plate 280758-00 Housing 280302-00 Shaker Plate 280759-00 Belt 280757-00 Motor Pulley 280756-00 Motor Plate 280720-00 Power Supply 380762-00 10. PC Board 380806-00 11. Motor Connection Cable 380765-00 12.
- Page 15 3500 ePlaceMent arts tandard DESCRIPTION PART NUMBER Rubber mat 480004-00 Thumbscrew 580001-00 Tray 280700-00 Top plate 280703-00 V-belt 580000-00 Motor 280633-00 Power supply 380623-00 IEC power inlet, 120V 380506-00 IEC power inlet, 230V 380237-00 Knob 287010-00 10. Rocker switch 349025-00 11.
- Page 16 3500 ePlaceMent arts dvanced DESCRIPTION PART NUMBER Rubber mat 480004-00 Thumbscrew 580001-00 Tray 280700-00 Top plate 280703-00 V-belt 580000-00 Motor 280633-00 Power supply 380623-00 IEC power inlet, 120V 380506-00 IEC power inlet, 230V 380237-00 Front panel 380803-00 10. Control circuit board 380806-00 11.
- Page 17 3750 ePlaceMent arts dvanced DESCRIPTION PART NUMBER Rubber mat 480004-00 Thumbscrew 580001-00 Tray 280533-00 Top plate 280531-00 V-belt 580000-00 Motor 280633-00 Power supply 380623-00 IEC power inlet, 120V 380506-00 IEC power inlet, 230V 380237-00 Front panel 380803-00 10. Control circuit board 380813-00 11.
- Page 18 & a 5000 ePlaceMent arts tandard dvanced DESCRIPTION PART NUMBER Rubber mat 280809-00 Thumbscrew 580001-00 Tray 280804-00 Top plate 280806-00 V-belt 580000-00 Motor 280633-00 Power supply, 24V 380623-00 Power entry module 386122-00 Advanced digital membrane switch 380803-00 10. Display circuit board 380813-00 11.
- Page 19 10000 - 150000 ePlaceMent arts dvanced DESCRIPTION PART NUMBER Feet 580017-00 Front bezel 280501-00 Advanced digital membrane switch 380803-00 Display circuit board 380813-00 Line filter 387022-00 Power supply, 386331-00 Cable, RS-232, 33” 345153-00 Power entry module 386122-00 Photosensor mounting bracket 280820-00 10.
- Page 20 latforM sage hart Platform Size Platform Type Used on Shaker Model Number Part Number 11 x 13” Universal Model 3500, Model 3750 89027-702 13 x 13” Universal Model 3500, Model 3750 97003-586 18 x 18” Universal Model 3500, Model 3750** 97003-588 18 x 24”* Universal...
- Page 21 lask laMP latforM aPacity Stainless Steel Erlenmeyer Flask Clamps Platform Part 10mL 25mL 50mL 125mL 250mL 500mL 2.8L Size Number 57018-775 57018-786 57018-797 57018-800 57018-811 57018-822 14215-224 14215-226 14215-228 10789-250 14215-230 14215-232 11 x 13 89027-702 13 x 13 97003-586 18 x 18 97003-588 18 x 24...
- Page 22 latforM aPacity Half Size Stationary 1.5 to 2mL 10 to 13mm 14 to 16mm 18 to 20mm 22 to 25mm 15mL Centrifuge 50mL Centrifuge Platform Part Microtube Rack Test Tube Rack Test Tube Rack Test Tube Rack Test Tube Rack Test Tube Rack Test Tube Rack Size...
- Page 23 ’ latforM aPacity cont 13mm Test Tube Rack 16mm Test Tube Rack 20mm Test Tube Rack 25mm Test Tube Rack 30mm Test Tube Rack Platform Size Part Number capacity = 90 capacity = 60 capacity = 40 capacity = 24 capacity = 21 97003-636 97003-638...
- Page 24 Manufactured by: Troemner, LLC 201 Wolf Drive • PO Box 87 • Thorofare, NJ 08086-0087 Phone: 856-686-1600 • Fax: 856-686-1601 • E-mail: troemner@troemner.com www.troemner.com 715077-00 (REV 16 - 8/16)