Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Westermo DDW-100
Summary of Contents for Westermo DDW-100
- Page 1 User Guide DDW-100 6621-2201 Industrial Ethernet SHDSL Extender www.westermo.com...
-
Page 2: Care Recommendations
Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical part may be damaged. If the unit is not working properly, contact the place of purchase, nearest Westermo dis- tributor office or Westermo Tech support. -
Page 3: Agency Approvals And Standards Compliance
CSA 22.2 No 60950-1-03* SHDSL ITU-T G.991.2, G.SHDSL standard* * Approvals according to Westermo standard, in the Beta-release approvals may not be completed. FCC Part 15.105 Notice: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable pro-... -
Page 4: Declaration Of Conformity
Declaration of Conformity 6601-2201... -
Page 5: Type Tests And Environmental Conditions
35 x 121 x 119 mm Weight TBD kg Degree of protection IEC 529 Enclosure IP 21 Cooling Convection Mounting Horizontal on 35 mm DIN-rail * Approvals according to Westermo standard, in the Beta-release approvals may not be completed 6601-2201... -
Page 6: Functional Description
Functional description SHDSL represents the best of several symmetric DSL technologies that has been com- bined into a single industry standard. DDW-100 is designed as a transparent Ethernet Extender for 10/100BaseTX networks, it is transparent for multicast addressing, VLAN packages, VPN pass through for IPSec and for protocols like MODBUS. -
Page 7: Getting Started
Getting started DDW-100 is easy to use and install, the units work in pair, one as have to be configured as CO (Central Office) and one as CPE (Customer Premises Equipment).This configura- tion is made by DIP-switches placed under the lid in DDW-100. -
Page 8: Interface Specifications
Interface specifications Power Rated voltage 12 to 48 VDC Operating voltage 10 to 60 VDC Rated current TBD // TBD mA @ 12 VDC // TBD // TBD mA @ 24 VDC // TBD // TBD mA @ 48 VDC // Rated frequency Inrush current, I2t TBD // TBD A2s //... - Page 9 RS-232, Diagnostic port intended for support purpose * Electrical specification RS-232/V.24 Data rate 115.2 kbit/s Data format 8 data bits, none parity, 1 stop bit Protocol Transparent Retiming Circuit type SELV Transmission range 15 m Isolation to 2000 Vrms to power interface 1500 Vrms to Ethernet interface 1500 Vrms to SHDSL interface Galvanic connection to...
- Page 10 Mounting This unit should be mounted on 35 mm DIN-rail, which is horizontally mounted inside an apparatus cabinet, or similar. Snap on mounting, see figure. Cooling 10 mm * (0.4 inches) This unit uses convection cooling.To avoid obstructing the air- 25 mm flow around the unit, use the following spacing rules.
- Page 11 SHDSL 4-position Description No. 1 Common No. 2 DDW-100 supports redundant power connection. The positive input are +VA and +VB, the negative No. 3 input for both supplies are COM. The power is No. 4 Common drawn from the input with the highest voltage.
-
Page 12: Led Indicators
LED Indicators Status Indication of Unit has no power Internal power Slow flash Initialisation progressing Fast FLASH Initialisation error DSL * Unit is unconnected Flash 1 (200 ms) Unit is initializing DSL, only CO Flash 2 (400 ms) Unit is in activation phase 1of DSL link establishment FLASH 3 (1 s) Unit is in activation phase 2 of DSL link establishment Unit has established a DSL connection... -
Page 13: Dip Switch Settings
DIP-switch settings Before DIP-switch settings: Prevent damage to internal electronics from electrostatic discharges (ESD) by discharging your body to a grounding point (e.g. use of wrist strap). NOTE DIP-switch alterations are only effective after a power on. A setting configured by any other method during normal operation, overrides the DIP-switch setting. -
Page 14: Block Diagram
Application Block diagram DIAGN. PORT* 8-pos. DIP-switch Ethernet Interface Isolation RJ-45 Connector SHDSL modem Memory Power SHDSL Power Link Isolation RJ-11 Connector Screw Screw Connector Connector * Diagnostic port is not implemented in the Beta version 6601-2201... - Page 15 DDW-100 as an transparent Ethernet extender Network Network 6601-2201...
- Page 16 Tél : +33 1 69 10 21 00 • Fax : +33 1 69 10 21 01 Phone: +44(0)1489 580 585 • Fax.:+44(0)1489 580586 E-mail : infos@westermo.fr E-Mail: sales@westermo.co.uk Westermo Teleindustri AB have distributors in several countries, contact us for further information.
Need help?
Do you have a question about the DDW-100 and is the answer not in the manual?
Questions and answers