Getting Started - TEFAL QUICK & HOT AQUA BR303 Manual

Notice Tefal AQUA 0827778:Mise en page 1
- Do not fill the tank with
hot water, milk or any
other liquid.
- Make sure that no
foreign bodies, such as
little stones, get into the
water tank: any damage
arising from foreign
bodies having entered
the tank is excluded
from the guarantee.
- Make sure that the
water is fresh from the
tap so that it has not
had time to become
stagnant in contact with
the air and that it is
odour-free.
- Never remove the tank
while the appliance is in
operation.
- If you use an entire
tank of water all at once
(approximately 1.5
litre), let the appliance
rest for 10 minutes
before launching a
new cycle.
Descaling your appliance
In order to optimise the lifetime of your appliance, we recommend that you descale it at least every 2 months.
Descaling should be carried out more frequently if you live in a very hard water area.
Certain models also have an indicator light
K
indicator is on during use, it is time to descale the appliance.
To descale:
1 Remove the Claris filter cartridge
2 Place a container of at least 1.5 litres under the nozzle.
12
9/05/07
All manuals and user guides at all-guides.com
1 Place the appliance on a flat, stable heat-resistant surface away from
water splashes and any sources of heat. Plug the appliance into the mains.
2 After having removed the lid
fig 1a b
and
3 Put the tank back in place by pressing firmly and reposition the lid
4 Place the desired container under the nozzle
5 Briefly press the hot water button
220 ml of hot water
Press again on same button if you wish to stop water before the cycle
comes to an end.
If you would like a greater or lesser amount of water, hold down the
button until you obtain the desired quantity of hot water
as you release the button, the hot water stops running.
Follow the same procedure with the the ambient water button
200 ml of water at room temperature
If you would like to get ambient water after hot water has been running,
fill half a mug and throw it away or wait 5 minutes as a minimum.
If you would like to get hot water after ambient water has been running,
fill half a mug and throw it away.
6 With certain models, you have the possibility of presetting the amount of
water automatically delivered by the appliance yourself.
To programme the amount for the hot water button
H
water and ambient water
K
indicator light flashes to indicate that you are now in programming
mode. Then press the hot water button
amount of water in your container
amount by simultaneously pressing buttons
turn off at the end of the programming mode.
To programme the amount for the ambient water button
same procedure as for programming the hot water button
ambient water button
7 The models with a quantity selector offer an additional function: you can
adjust the amount of water automatically delivered to your container. To
do this, select the chosen amount on the rotary button
container, then briefly press the hot water button
or the ambient water button
will stop automatically
8 If you are using small cups, we recommend that you hold the cup close to
E
the nozzle to avoid any splashes.
9 To ensure minimal energy consumption from this appliance please switch
off your plug point when the product is in use.
K
, which indicates when descaling is necessary. When this
fig 6.
17:05 Page 12

Getting started

B
, remove and fill the tank
E
.
H
and you will automatically obtain
fig 8.
The water will stop running automatically.
fig 9 fig 10.
or
G
buttons simultaneously
H
until you obtain the desired
fig 3.
Finally confirm the recorded
G
and
G
to obtain the desired amount of water
G
to obtain ambient water; the water flow
fig 11.
A
with cold water.
B fig 2.
.
fig 3.
As soon
G
to obtain
H
, press both hot
fig 7
. The
H fig 7
. The light will
G
, follow the
H
, pressing the
fig 10.
I
, according to your
H
to obtain hot water