Table of Contents
Advertisement
2 - Names and Functions of Parts
w INPUT 2 volume
Use this to manually adjust the input level when the LEVEL
switch (0) is set to "MAN".
Minimizing the volume will mute the input.
The input adjustment that is possible depends on the
following switch settings.
SELECT
1+2 LINK
switch (2)
switch (8)
IN 3
—
ON
IN 1+2
OFF
ON
IN 1
OFF
NOTE
i If the LEVEL switch (0) setting is "AUTO", adjustment of the
input volume will have no effect.
i Distortion might occur when signals that are very loud are
input even if the LIMITER switch (q) is set to "ON". In such
a case, lower the recording level or increase the distance
between the mic and the sound source.
e Accessory shoe (cold shoe)
This accessory shoe is a cold shoe.
ATTENTION
i Do not connect accessory shoe devices that have connectors
or other parts that stick out. Doing so could damage this unit
and the connected device.
i Do not attach heavy equipment. Doing so could cause
damage or their falling off due to their weight.
r OUTPUT switch
Set the output setting according to the equipment
connected to the OUTPUT jack (t) and the application.
Use this setting when connecting to a camera mic
or line input jack.
Operation of the
have no effect.
Use this setting when connecting headphones.
Operation of the
adjust the headphone output level.
ATTENTION
Do not use with an analog connection to a camera when
set to . If used with the
VOLUME +/− buttons (y) near
maximum level, excessive input could occur depending on
the camera input specifications, possibly resulting in damage
to the connected devices.
NOTE
When set to "
", the level output from the OUTPUT jack is
fixed. Refer to the list of cameras that have been confirmed
for operation on the TASCAM website (https://tascam.jp/int/
product/ca-xlr2d/docs) when setting the camera input gain
value.
6
TASCAM CA-XLR2d
Input volume operation
Adjustment of the input volume
will have no effect.
Adjustment of the input volume
will have no effect.
Use to adjust the input level of
the INPUT 2 jack.
Adjustment of the input volume
will have no effect.
Use to adjust the input level of
the INPUT 1 jack (R channel).
VOLUME +/− buttons (y) will
VOLUME +/− buttons (y) will
t OUTPUT jack
This can be used in two ways, either as a headphone output
for monitoring the analog sound with headphones or as a
camera output to connect the analog sound to a camera.
Set the OUTPUT switch (r) output setting according to the
equipment connected and the application.
ATTENTION
i Do not use with an analog connection to a camera when
set to . If used with the
VOLUME +/− buttons (y) near
maximum level, excessive input could occur depending on
the camera input specifications, possibly resulting in damage
to the connected devices.
i To monitor the analog connection to a camera use TASCAM
AK-DR11C or AK-DR11CMKII splitter and attenuator cables.
(see "Monitoring through this unit (CA-XLR2d-AN)" on page
16)
y VOLUME +/− buttons
i If the OUTPUT switch (r) is set to "
of the OUTPUT jack (t) can be adjusted (25 levels total).
i The volume can be reset to its center value by pressing
the + and − buttons at the same time. The setting from
previous use is retained when the power is turned on
again.
V CAUTION
Continuously pressing the
sudden loud noises, which could harm your hearing or result
in other trouble.
u Mic holder
This holder can be used to mount mics with 19–23 mm
diameters. (see "Connecting a single mic that uses phantom
power" on page 12)
When not being used, it can be removed. (see "Removing the
mic holder" on page 13)
i INPUT 1 jack
This input jack is for mics and other recording devices.
Phantom power is supported.
ATTENTION
i Before connecting or disconnecting a mic or other recording
device, turn this unit off.
i Do not connect or disconnect mics when the INPUT 1 switch
(4) is set to +48V. Doing so could cause a loud noise and
might damage this unit and connected equipment.
i Do not set the INPUT 1 switch (4) to "+48V" when
connecting mics that do not require phantom power.
i When using a single mic, connect it to the INPUT 1 jack.
o Cable holder
This is a holder for mic cables.
Wrap and fix cables appropriately so that noise is not caused
by loose or pulled cables.
", the output volume
VOLUME + button might cause
Advertisement
Table of Contents
