Onkyo TX-DS595 Instruction Manual page 26

Enjoying music or videos with the TX-DS595
DISPLAY
STANDBY/ON
STANDBY
POWER
ON OFF
PHONES
AUDIO SELECTOR
Selecting speakers (SPEAKERS A, B)
SPEAKERS A: This button turns on or off the speakers connected
to the FRONT SPEAKERS, CENTER SPEAKER, SURROUND
SPEAKERS, and SUBWOOFER terminals.
When you listen to surround audio or select multi channel input, be
sure to turn on SPEAKERS A.
When the speakers are turned on, the SPEAKERS A indicator lights
up.
SPEAKERS B: This button turns on or off the speakers connected
to the FRONT SPEAKERS B terminals.
When the speakers are turned on, the SPEAKERS B indicator lights
up.
Notes:
• You cannot select surround sound when you are using
SPEAKERS B.
• When using the B speakers, the A speakers can only be used for
stereo or direct playback, so nothing will be output from the left
and right surround speakers during multichannel playback.
Adjusting the volume
Adjusting the main volume adjusts the volume level output from all
the speakers connected to the TX-DS595 together. If headphones are
connected, this also adjusts the volume heard from the headphone
speakers. To adjust the volume, either press the VOL
the remote controller or turn the MASTER VOLUME dial. To
increase the volume, turn the dial clockwise; to decrease the volume,
turn the dial counterclockwise. The volume can be set to Min, 1 to
79, and Max.
Adjusting the bass and treble
You can adjust the bass and treble levels using the BASS and
TREBLE dials. This function only affects the front left and right
speakers. For multichannel sources, these dials will not work if the
tone control is set to "OFF." (Refer to page 27.)
Temporarily turning off the sound (Remote
controller only)
To turn off the sound momentarily, such as when interrupted by a
phone call, press the MUTING button on the remote controller.
When pressed, "MUTING" is displayed on the TX-DS595. Press the
MUTING button again to turn the sound back on.
26
SPEAKERS A/B
Jog dial
CH LEVEL
A SPEAKERS B
CH LEVEL
DSP / MODE ADJ SETUP
RETURN
PUSH TO ENTER
DISPLAY DIMMER FM MODE PRESET MEMORY TUNING PRESET SMART SCAN NAVIGATOR
AUDIO
DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE FM AM PHONO C D
SELECTOR
VCR
BASS
buttons on
MASTER VOLUME
SLEEP
RCVR
MODE
MASTER VOLUME
CH SEL
AUDIO
BASS TREBLE
TX-DS 595
AV RECEIVER
TREBLE SP A, B
DISPLAY
Switching the display
While listening to or watching an input source, you can display the
information regarding the type of source and signal being input by
pressing the DISPLAY button on the TX-DS595 or the remote
controller.
When an input source other than FM or AM is selected:
Input + volume
Program format*
Input +
Listening mode
or MULTI CH
* If the input signal does not have a program format, then this will
be skipped.
When FM or AM is selected as the input source:
FM/AM frequency +
Preset no.
FM/AM +
Listening mode
Using the sleep time (Remote controller only)
The SLEEP button enables you to set the TX-DS595 to turn off
automatically after a specified time period. If you press it once, the
TX-DS595 will turn off after 90 minutes. Each time it is pressed
thereafter, the remaining time until the TX-DS595 turns off
decreases by 10 minutes. While, the sleep function is enabled, you
can press the SLEEP button to see how much time is left. To cancel
the sleep function, press the SLEEP button when the time displayed
is less than 10 minutes.
VOL
C H
VOL
DISC
AUDIO MUTING MUTING
ANGLE SUBTITLE
TV / VCR
LEVEL
LEVEL
RANDOM OPEN / CLOSE
REC
DVD C D
V 1 V 2 T 1 T 2
V 3 V 4 TUN P H
STEREO DIRECT DSP
1 2 3
SURR A.ST DSP
4 5 6
SP A SP B Re-EQ
7 8 9
DISPLAY DIMMER ZONE 2
+10 0
SEARCH
-- / ---
ENTER
HOME THEATER CONTROLLER
RC-447M
ch