Connecting Your Video Components - Onkyo TX-DS595 Instruction Manual

Connections
Video output
4. DVD player
(DVD)
S video output
Analog audio output
Digital audio output (Coaxial)
: Signal flow
Audio connection cable
Left (White)
Right (Red)
7. TV monitor or Projector
(MONITOR OUT)

Connecting your video components

Below is an example of how you can connect your video
components to the TX-DS595. Refer to the diagram above for the
following connection examples.
The flow of the video signals is as follows:
• The signal that comes in from VIDEO IN is sent to VIDEO
OUT.
• The signal that comes in from S VIDEO IN is sent to S VIDEO
OUT
4. Connecting a DVD player (DVD)
If the device is equipped with an S video output terminal, connect it
to the DVD S VIDEO IN terminal with an S video cable. If it does
not have an S video output terminal, connect its video output
terminal to the DVD VIDEO IN terminal using an RCA-type video
connection cable. You do not need to connect to both the DVD S
VIDEO IN and DVD VIDEO IN terminals.
Using an RCA-type audio connection cable, connect the audio
output terminal on the device to the audio DVD IN jacks on the TX-
DS595. Make sure that you properly connect the left channel to the L
jack and the right channel to the R jack.
12
MONITOR DVD
OUT
IN
REMOTE
CONTROL
NO CD TAPE
OUT IN
L (White)
FRONT SURR CENTER
L
R (Red)
R
SUB
ER WOOFER
MULTI
UT CHANNEL INPUT
L Video connection cable
R
MONITOR
OUT
Video input
S video input
REMOTE
CONTROL
NO CD TAPE
OUT IN
FRONT SURR CENTER
L
R
SUB
ER WOOFER
MULTI
UT CHANNEL INPUT
VIDEO 1 VIDEO 2 VIDEO 3
OUT IN IN IN
VIDEO
VIDEO
S VIDEO S VIDEO
L L
R
R
OPTICAL COAXIAL
1 2
1
2
DIGITAL INPUT
DVD VIDEO 1 VIDEO 2 VIDEO 3
IN OUT IN IN IN
VIDEO
S VIDEO
L
R
OPTICAL COAXIAL
1 2
1
2
DIGITAL INPUT
If the device has a digital output jack as well, be sure to also connect
it to either a DIGITAL INPUT (COAXIAL) or DIGITAL INPUT
(OPTICAL) jack on the TX-DS595 depending on the type of
connector on the DVD player.
With the initial settings of the TX-DS595, the DVD input source
is set for digital input at the COAXIAL 1 jack.
If the digital connection is made at a different jack, this must be
changed at the setup menu: Input Setup
Input (see page 29).
5. Connecting a video cassette recorder (VIDEO 1)
If the video cassette recorder is equipped with an S video output
terminal, connect it to the S VIDEO 1 IN terminal with an S video
cable. If it does not have an S video output terminal, connect its
video output terminal to the VIDEO 1 IN terminal using an RCA-
type video connection cable. You do not need to connect to both the
S VIDEO 1 IN and VIDEO 1 IN terminals.
Using an RCA-type audio connection cable, connect the audio
output terminal on the video cassette recorder to the same VIDEO 1
IN audio jacks on the TX-DS595 and audio input terminal to the
VIDEO 1 OUT audio jacks. Make sure that you properly connect the
left channel to the L jack and the right channel to the R jack.
V
Video output
S video
S video output
L (White)
Analog audio output
R (Red)
Digital audio output
(Coaxial)
5. VCR (VIDEO 1)
Video input
S video input
R (Red)
Analog audio input
L (White)
S Video connection cable
Video output
S video output
6. Satelite tuner, TV,
L (White)
or settop box
(VIDEO 2 / VIDEO 3)
R (Red)
Analog audio output
Digital audio output (optical)
→
Audio Setup
→
Digital