Operation - Milwaukee MX FUEL MXF CVBP Operator's Manual

Removing/Installing the Backpack
The backpack can be removed for certain applica-
tions or for spot cleaning.
To remove the backpack, squeeze the backpack
latch and pull the backpack away from the machine.
NOTE: When used without a backpack, do not drag
the machine with the flexible shaft.
To install the backpack, line up the bottom hook and
secure the backpack to the machine base using the
backpack latch.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this machine, please refer to the quick reference
included with this
onekey.milwaukeetool.com.au
onekey.milwaukeetool.co.nz. To
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready
app.
Blinking Blue Machine is actively communicating
with the ONE-KEY™ app.
Blinking Red Machine is in security lockout and
can be unlocked by the owner via
the ONE-KEY™ app.

OPERATION

To reduce the risk
WARNING
wear proper eye protection marked
to comply with AS/NZS 1337.1.
Arming the Machine
The MX FUEL™ machines must be armed prior to
use. Even with the battery pack inserted, the machine
functions will not operate until the machine is armed.
To arm the machine:
1. Insert the battery pack.
2. Press the Arm button. The MX FUEL™ symbol
will illuminate.
3. After 15 minutes of inactivity, the machine will
enter sleep mode. The MX FUEL™ symbol and
other operational LED's will no longer be
illuminated.
4. Press and hold the Arm button for 1 second to
reactivate the machine.
5.
Press and hold the ARM button for 1 second to
unarm (turn off) the machine. The MX FUEL™
symbol will go off.
Starting and Stopping
1. Arm the machine.
2. To start the machine, set the switch to the
position.
3. To stop the machine, set the switch to the
position.
Starting and Stopping (Remote Mode)
1. Arm the machine.
2. On the machine, set the switch to the
3. Turn on the remote
4. To start the machine, press the
remote.
5. To stop the machine, press the
remote.
machine or go
download
of injury, always
position.
button on the
button on the
The Cold Start LED will illuminate when the
machine is started in cold conditions (below 0°C).
The machine will will gradually bring the VPM up to
10,000 in order to avoid nuisance shut downs. Once
the VPM reaches 10,000 VPM the Cold Start LED
will go off. This feature allows the machine to start in
temps as low as -20°C.
Low Battery Alert
During use, when the battery nears end of charge
(at 10% and 2% remaining charge), the machine
will notify the user by turning itself off and on
(pausing). Remove the battery from the backpack
and charge the battery with a MX FUEL™ battery
to
charger.
/
the
General Operation
1. Turn the unit on before putting head in material.
Insert the head vertically into material allowing
2.
the head to sink to desired depth by its own
weight.
Hold in place for 5-15 seconds, then slowly lift
3.
head up, keeping the shaft and head in front of
your operating position, while staying behind the
trapped air's movement to avoid retrapping air.
A small up and downward movement will close
4.
the hole formed by the head.
To prevent agitating air into material, withdraw
5.
the head quickly when near the top. Move head,
re-insert and repeat as desired.
6. When task is completed, remove head from
material, then turn machine off.
CAUTION
will be difficult to remove.
CAUTION
turned off. Turn machine off as quickly as possible
once head removed from material.
5
Cold Start LED
If machine is turned off before
removing head from material, head
Material may spray once head is
removed and prior to machine being