Download  Print this page

Normal Playback; Preparing For Playback - Kenwood VR-905 Instruction Manual

Kenwood instruction manual audio video surround receiver vr-906 vr-905 krf-v6090d krf-v5090d
Hide thumbs

Advertisement

Preparing for surround sound
3 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to select the distance to the front speakers.
Indication in feet Indication in meters
• The allowable setting range is 1 to 30 feet (0.3m to 9.0m),
adjustable in 1 foot (0.3m) increments.
4 Press the SETUP key to accept the settings.
5 Repeat steps 3 and 4 to input the distance for each of the
speakers.
6
Adjust the LFE (Low Frequency Effects) level.
1 Select the LFE LEVEL from the set up displays and press the
SETUP key again.
2 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys
to adjust the LFE LEVEL.
• The LFE LEVEL can be adjusted from 0dB to -10dB in 1dB step
decrements.
3 Press the SETUP key to accept the setting.
4 Setup is complete when the EXIT indication appears.
• The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
5 Press the SETUP key to exit the SETUP mode.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
1 Use the INPUT SELECTOR knob to select the source of which the
input level you want to adjust.
• You can store a separate input level for each input source.
2 Press the SOUND key repeatedly until the "INPUT" indication
appears.
3 Use the MULTI CONTROL knob or MULTI CONTROL %/fi keys to
adjust the input level.
• The input level may be adjusted to any one of three settings: 0dB,
-3dB, and -6dB. (The initial setting is 0dB.)
4 Press the SOUND key again to return to the input indication.
18
EN

Normal playback

Preparing for playback

Some preparatory steps are needed before starting playback.
SPEAKERS
ON/STANDBY
ON/OFF
(VR-906/VR-905)
POWER
AUTO/MONO INPUT SELECTOR
ON/OFF
(KRF-V6090D/
KRF-V5090D)
Turning on this model
1 Turn on the power to the related components.
2 Turn on the power to this model by pressing POWER ON/
STANDBY
(VR-906/VR-905) or POWER ON/OFF and ON/
STANDBY
(KRF-V6090D/KRF-V5090D) key.
Selecting the input mode
If you have selected a component connected to the CD/DVD, VIDEO2,
DVD (VR-906/VR-905) or DVD/6CH (KRF-V6090D/KRF-V5090D) jacks,
make sure that the input mode setting is correct for the type of audio
signal to be used.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is "TAPE". To change the
source to "MD", follow the steps below:
1 Use the INPUT SELECTOR knob to select "TAPE".
2 Hold down the AUTO/MONO key for more than 2 seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat procedure 2.
Setting the speaker status
The speaker indicator lights up.
Press the SPEAKERS ON/OFF key to switch the speaker on or off.
POWER
ON/STANDBY
(KRF-V6090D/
KRF-V5090D)
8

Advertisement

loading

  Also See for Kenwood VR-905

  Related Manuals for Kenwood VR-905

This manual is also suitable for:

Krf-v5090dKrf-v6090dVr-906