Download  Print this page

Setting Up The System - Kenwood VR-905 Instruction Manual

Kenwood instruction manual audio video surround receiver vr-906 vr-905 krf-v6090d krf-v5090d
Hide thumbs

Advertisement

Setting up the system

Make connections as shown in the following pages.
When connecting the related system components, be
sure to refer to the instruction manuals supplied with
the components you are connecting.
Do not connect the power cord to a wall outlet until all
connections are completed.
Notes
1. Be sure to insert all connection cords securely. If their connections are
imperfect, the sound may not be produced or there will be noise
interference.
2. Be sure to remove the power cord from the AC outlet before plugging
or unplugging any connection cords. Plugging/unplugging connection
cords without disconnecting the power cord can cause malfunctions
and may damage the unit.
3. Do not connect power cords from components whose power
consumption is larger than what is indicated on the AC outlet at the
rear of this unit.
Analog connections
Audio connections are made using RCA pin cords. These cables transfer
stereo audio signal in an "analog" form. This means the audio signal
corresponds to the actual audio of two channels. These cables usually
have 2 plugs at each end, red for the right channel and white for the left
channel. These cables are usually packed together with the source unit,
or are available at your local electronics retailer.
Microcomputer malfunction
If operation is not possible or an erroneous display appears, even
though all connections have been made properly, reset the
microcomputer by referring to "In case of difficulty".
8
EN
Input mode settings
CD/DVD, VIDEO2, DVD(VR-906/VR-905) and DVD/6CH(KRF-
V6090D/KRF-V5090D) inputs each include jacks for digital audio
input and analog audio input.
After completing connections and turning on this model, follow the
steps below.
LISTEN MODE
INPUT MODE
1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2,
DVD (VR-906/VR-905 only), DVD/6CH (KRF-V6090D/KRF-
V5090D only).
2 Press the INPUT MODE key.
Each press switches the setting as follows:
In DTS play mode
1 F-AUTO (digital input, analog input)
2 D-MANUAL (digital input)
In CD/DVD, VIDEO2, DVD(VR-906/VR-905 only), DVD/
6CH(KRF-V6090D/KRF-V5090D only) play mode
1 F-AUTO (digital input, analog input)
º
2 D-MANUAL (digital input)
3 6CH INPT (DVD/6CH input) (KRF-V6090D/KRF-V5090D only)
4 ANALOG (analog input)
Digital input:
Select this setting to play digital signals from a DVD, CD, or LD
player.
Analog input:
Select this setting to play analog signals from a cassette deck, VCR,
or record player.
Auto detect:
In "F-AUTO" (full auto) mode (AUTO DETECT and DIGITAL
indicators light up), this model detects the digital or analog input
signals automatically. Priority is given to digital signal during input
mode selection. This model will select the input mode and listening
mode automatically during playback to match the type of input
signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial
factory setting is full auto.
To keep this model set to the currently selected listening mode, use
the INPUT MODE key to select "D-MANUAL" (digital manual).
However, even when this setting is selected, there may be cases
in which the listening mode is selected automatically to match a
Dolby Digital source signal depending on the combination of listening
mode and source digital.
In D-MANUAL mode, if the audio reproduction stops in the middle
due to change in the input signals etc, press the LISTEN MODE key.
If the INPUT MODE key is pressed quickly, sound may not be
produced. Press the INPUT MODE key again.
INPUT SELECTOR

Advertisement

loading

  Also See for Kenwood VR-905

  Related Manuals for Kenwood VR-905

This manual is also suitable for:

Krf-v5090dKrf-v6090dVr-906