Changing The Temperature During Cooking; Changing The Time During Cooking; Keep Warm Function (Automatic Heating); Reheat - Redmond RMC-PM400 User Manual

Changing the temperature during cooking

Available only for programmes operating in multicooker mode (except the "ЭКСПРЕСС" program).
The range and increment of cooking temperature depend on the selected program (see "Table
of Default Settings" section), interval — 1 °С.
1. When a cooking program runs, press the
starts to blink.
2. Press the — — and + + buttons to set the desired temperature value. The programs are switched
circle-wise. For rapid change of a value, press and hold the appropriate button.
3. Do not press any button on the control panel for several seconds. The changes are saved
automatically (the value on the display finished to blink).
To protect against overheating, the maximum running time of a program is limited to 2 hours
when the cooking temperature is set above 150°С.
When changing the cooking time while achieving the working characteristics (if it is provided
by the factory settings), the preheating process is interrupted. The countdown of a program
running starts.

Changing the time during cooking

The range of cooking time depend on the selected program (see Table of Default Settings),
interval — 1 minute.
1. When a cooking program runs, press the
2. Press the — — and + + buttons to set the desired hour value. The programs are switched
circle-wise. For rapid change of a value, press and hold the appropriate button.
3. Press the button to save the entered changes and to go to the minute value setting.
4. Set the minute value in the same manner. Do not press any button on the panel for several
seconds. The changes are saved automatically. (the value on the display finished to blink).
To return to the hour value setting before autosave, press the
If you set the cooking time to 00:00, the program stops running after autosave.
If you change the cooking time while reaching the operating parameters of the programme
"ЖАРКА/ФРИТЮР", preheating is interrupted and the programme time starts counting down.

Keep Warm Function (automatic heating)

This function is not available on all programmes (see "Table of Default Settings" section).
This function automatically activates at the end of the cooking cycle and keeps the food warm
at 70-75°С for 12 hours. When Keep Warm is active, the
light up and the display indicates the direct time count of running in this mode. If necessary,
the Keep Warm may be disabled by pressing the
mode (– – – – on the display).
Enabling the Keep Warm upon completion of a cooking program is not always desirable. Taking
into account this fact, the device provides an option to timely disable this function while
button. The temperature value on the display
button. The hour value on the display starts to blink.
button once again.
button indicator and indicator
button. The device goes to the standby
running of the main cooking program. For this purpose, while running of a program or Time
Delay function press the button: the
To enable the Keep Warm again, press the
For user"s convenience, the Keep Warm is disabled automatically without option to enable it
manually when the cooking temperature is set below 80°C. While running a program, the
temperature is set above 80°C, the Keep Warm enables automatically.

Reheat

The device can be used to reheat cold dishes. Proceed as follows:
1. Put all products to the bowl, install the bowl into the device frame.
2. Close the lid, connect the device to electrical outlet.
3. Press and hold the button for a several seconds. The
indicator light up, the timer begins to count the heating time. Once the temperature
achieves 70°С, the device gives two short audible signals.
The device reheats the dish up to 70-75°С and keeps it hot for up to 12 hours. If necessary,
reheat can be stopped by pressing the
(– – – – on the display).
Thanks to the Keep Warm and Reheat functions, the Electric Pressure Cooker can keep a product
hot for up to 12 hours. However, it is not recommended to leave a dish hot for more than 2-3 hours
since sometimes this may result in change of its taste.

Safety System

REDMOND RMC-РМ400 Electric Pressure Cooker is equipped with the multi-level safety system.
If temperature and/or pressure in chamber exceed the permissible limits, the system normalizes
these characteristics automatically without interruption of cooking process. If this fails to
happen for a certain period of time, the operation of Electric Pressure Cooker is stopped, and
the device gives 6 short audible signals.
In case of interruption of the cooking process in the pressure cooker mode by pressing the
button (or de-energizing the device while running a program), let the device cool for several
minutes, then press and hold the open steam valve button to normalize the pressure in the
bowl; then open the lid of the appliance.

Table of Default Settings

Programme Recommendations for use
Cooking various grains and side
РИС/КРУПЫ* 0:10
dishes
RMC-PM400
indicator and the button indicator goes off.
button once again.
button indicator and
button. The device goes to the standby mode
Cooking
temperature
range /
setting step
1 min – 2 h /
   
1 min
GBR
UKR
KAZ
,
11