Setting Cooking Time; Setting Cooking Temperature; Setting Pressure Level; Time Delay Function - Redmond RMC-PM400 User Manual

Press the button to cancel the entered program, interrupt the cooking process or Keep Warm.
DO NOT:
– fill the bowl with products and water over the maximum mark on the inner surface of the
bowl;
– cook in the pressure cooker mode without adding water or other fluid (min. required fluid
level is 2 measuring cups);
– use the pressure cooker mode to fry products on oil.
To obtain a high-quality result, you are suggested to use the recipes for cooking from the
cookbook attached to the pressure multicooker, designed specifically for this model. Relevant
recipes can also be found on the website www.redmond.company.

Setting Cooking Time

The device is provided with an option to set cooking time for each program manually, except
for "ЭКСПРЕСС" program. The change increments and the possible range of the set time depend
on the cooking program selected (see "Table of Default Settings" section).
1. After selecting an automatic program, press the
hour value on the display starts to blink.
2. Press the — — and + + buttons to set the desired hour value. The programs are switched
circle-wise. For rapid change of a value, press and hold the appropriate button.
3. Press the button to save the entered changes and to go to the minute value setting.
4. Set the minute value in the same manner. Do not press any button on the panel for several
seconds. The changes are saved automatically. (the value on the display finished to blink).
To return to the hour value setting before autosave, press the

Setting Cooking Temperature

When using the multicooker mode programs (except for the "ЭКСПРЕСС" program), it is possible to
change the cooking temperature before the start. The range and increment of cooking temperature
depend on the selected program (see "Table of Default Settings" section), interval — 1 °С.
1. After selecting an automatic program, press the button to set the cooking temperature.
The temperature default value on the display starts to blink.
2. Press the — — and + + buttons to set the desired temperature value. The programs are switched
circle-wise. For rapid change of a value, press and hold the appropriate button.
3. Do not press any button on the control panel for several seconds. The changes are saved
automatically (the value on the display finished to blink).
To protect against overheating, the maximum running time of a program is limited to 2 hours
when the cooking temperature is set above 150°С.

Setting Pressure Level

The function of pressure level adjustment before programme start is available for programmes
operating in pressure cooker mode. The maximum pressure level is set by default (the value
10
"6" is shown on the pressure level indicator). To change the pressure level, after selecting an
automatic programme, press the
corresponding value on the indicator lights up. The selected value is automatically saved.

Time Delay function

The Time Delay function enables setting of the time interval after which a cooking program
starts.
1. After selecting an automatic cooking program, press the
2. Press the — — and + + buttons to set the desired hour value. The programs are switched
3. Press the
4. Set the minute value in the same manner. Do not press any button on the panel for
button to set the cooking time. The
After autosave, the
After starting the program the
on the display. To see the time of cooking program, press the
seconds shows the set cooking time.
Once the function work is over, the device gives three short audible signals, the
goes off. Selected cooking program starts.
button once again.

MASTERCHEF LITE function

Open even more opportunities for culinary creativity with the new MASTERCHEF LITE feature!
Using the MASTERCHEF LITE function, you can change the settings directly in the cooking
process.
You can always configure the work of any program so that it corresponds to your wishes. Does
the soup boil away? Does the milk porridge "runs away"? Are the steamed vegetables cooked
for too long? Change the temperature or cooking time without interrupting the program, as
if you were cooking on the stove or in the oven.
The MASTERCHEF LITE function allows you to change the cooking time and temperature while
any automatic programme is operating.
button: switching is performed circle-wise, so the
This function is not available on all programmes (see "Table of Default Settings" section).
up. The hour value on the display starts to blink.
circle-wise. For rapid change of a value, press and hold the appropriate button.
button to save the entered changes and to go to the minute value setting.
several seconds. The changes are saved automatically (the value on the display finished
to blink). To return to the hour value setting before autosave, press the
again.
indicator goes off, the display will show the cooking time.
indicator lights up, the minute countdown timer is indicated
It is not recommended to use the Time Delay function, if the recipe contains perishable products
(eggs, fresh mild, meat, cheese, etc.)
The MASTERCHEF LITE function can be especially useful if you prepare dishes according to
complex recipes that require a combination of different cooking programs (for example, when
preparing cabbage rolls, beef Stroganoff, soups and pasta according to different recipes, jam,
etc.).
button, the . indicator lights
button once
button, the display for a few
indicator