To Clean The Housing, Lid And Sealing Ring; To Clean Removable Steam And Lock Valves; To Clean The Bowl; To Remove Condensate - Redmond RMC-PM400 User Manual

• Be careful when cleaning the rubber parts of Electric Pressure Cooker. Their damage or
deformation may result in an inappropriate operation of the device.
• Clean the housing when necessary. The bowl, lid and sealing ring, steam and lock
valves need to be cleaned after each use. Condensate, accumulating during cooking,
needs to be removed after each use. Clean the interior of the cooking chamber when
necessary.

To Clean the Housing, Lid and sealing ring

Use soft damp cloth or sponge to clean the housing and lid. If necessary, use a mild soap
solution. Wipe the surface dry to remove soap residue and water spots.
To remove the sealing ring, gently pull it towards you. Rinse under running water. If necessary,
use a mild soap solution. Dry at room temperature and install in the device.

To Clean Removable Steam and Lock Valves

1. Carefully pull the steam valve upwards and remove it.
2. Remove the steam valve cap on the inner side of the lid by pulling it towards you.
3. Carefully remove the lock valve rubber and remove the valve itself. Rinse all parts of the
valves.
4. Reassemble the valve in reverse order of disassembly. Place the lock valve back into its
original position, put the lock valve rubber on it, fit the steam valve cap to the thrusts
until tight. Tightly fix the steam valve to the slot on the lid of the appliance.
ATTENTION! To avoid deformation of the lock valve rubber, do not twist and pull it after removal,
cleaning and mounting.

To Clean the Bowl

The appliance bowl must be cleaned after each use. You can clean the bowl by hand, using a
soft sponge and dishwashing detergent, or in the dishwasher (according to the manufacturer's
recommendations).
If heavily dirty, fill the bowl with warm water and leave to soak for a while, then clean.
Wipe the outer surface of the bowl dry before positioning it back inside the multicooker.
When the bowl is used regularly, it is possible to completely or partially change the color of
the internal non-stick coating. This in itself is not a sign of a defect.

To Remove Condensate

In this model the condensate accumulates in the special cavity on the housing around the
bowl and drains into a special container, located on the back side of the appliance.
1. Open the lid, remove the bowl. If necessary slightly lift the front part of the electric
pressure cooker, so that condensate completely drains into the container.
2. Remove the container, slightly pulling it.
3. Pour the condensate out. Wash the container and insert into the place.
4. Wipe off any condensate remaining around the bowl with a dry cloth.
14

Cleaning the Working Chamber

Compliance with the user manual guidelines minimizes the risk of food particles or liquids
accumulating inside the cooking chamber.
However, if the inside of the chamber gets dirty, clean it to prevent improper operation or
malfunction of the unit.
Walls of the cooking chamber, surface of the heating disk, and the casing of central thermal
sensor (located in the middle of the heating disk) can be cleaned with a damp (not wet!)
sponge or cloth. Remove any traces of soap or detergent if using any to prevent unwanted
odors during cooking. If there is a foreign object in the cavity around central thermal sensor,
carefully remove it using tweezers, trying to avoid pressing on the casing of the sensor. Clean
heating disk with a damp medium-hard sponge or synthetic brush, if necessary.
During regular operation of the device, the heating disc may totally or partially change its color.
This is not a sign of the device failure and does not influence on its operation.

Storage and Transportation

Before repeated operation or storage completely dry all parts of the appliance. Store the
assembled appliance in a dry, ventilated place away from heating appliances and direct
sunlight.
During transportation and storage, do not expose the device to mechanical stress, that
may lead to damage of the device and/or violation of the package integrity.
Keep the device package away from water and other liquids.
VII. BEFORE CONTACTING THE SERVICE CENTRE
Problem Possible cause
Display shows the error code:
System error, possible control board or heating
Е*, the device gives 6 short
element malfunction
audible signals
A programme in the multicooker mode is running,
Display shows the error
the steam valve is set to operate in pressure cooker
code: Е4
mode
Display shows the error
The automatic overheating protection was triggered
code: Е5–E7
Solution
Unplug the appliance and let cool down.
Close the lid tightly and plug in the
appliance
Carefully pull the steam valve upwards
and remove it.
Do not start cooking with an empty bowl!
Disconnect the appliance from the mains,
open the lid and let it cool for 10-15
minutes, then continue cooking
Do not add water to the bowl during
operation of "ЖАРКА/ФРИТЮР" programs
If the temperature is set above 120°C
within the "ЖАРКА/ФРИТЮР" program,
cook with the lid open
Within the "ЖАРКА/ФРИТЮР"
programme, add the ingredients to the
bowl only after the appliance has
reached operating parameters.