Savant WPX LV06 Series Quick Reference Manual

Echo / Metropolitan Wireless Configurable Keypad for Basic DMX Control
Quick Reference Guide

Box Contents

(WPX-xxLV06, WIX-xxLV06)
(1) Keypad (faceplate not included)
(1) 4-pin Cable Control Station Pigtail (064-0417)
(2) Double Height Keypad Buttons (074-0927) - WPX Only
(2) Double Height Keypad Buttons (074-0808) - WIX Only
(1) Product Regulatory Statement (009-1950)

Optional Accessories

– One to Four Gang Wall Plates (FIx-0S0xxP)

Specifications

Environmental

Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Location Indoor Use Only
Dimensions and Weights
Length
WPX-xxLV06
4.13 inch
(10.50 cm)
WIX-xxLV06
7.0 inch
Shipping
(17.78 cm)

Installation Recommendations

Savant recommends as a minimum:
– An open-backed low voltage bracket installed on the interior
walls and a closed-back electrical box on exterior walls.
– An installation depth of at least 1

Power

Input 24V DC
Average Power
5W
Consumption
Maximum Power
12W
Consumption
Maximum Wiring (DMX keypad to DMX Driver )
#20 AWG 328 feet (100 meters)
#18 AWG 492 feet (150 meters)
#16 AWG 618 feet (188 meters)
#14 AWG 984 feet (300 meters)

Regulatory

FCC Part 15
Class B
Safety and
Emissions
RoHS Compliant
Minimum Supported Release
da Vinci 10.0
Wireless Configurable Keypad for DMX Control - QRG
Copyright© 2021 Savant Systems, Inc. | 009-2075-00 | 211015
Width Depth Weight
1.72 inch .97 inch .30 lb.
(4.37 cm) (2.46 cm) (0.13 kg)
4.5 in. 3.0 in. .60 lb.
(11.43 cm) (7.62 cm) (0.27 kg)
1/4
inches (3.2 cm).
CE Mark UKCA

Products

Configurable Keypad - Echo Style (WPX-xxLV06)
Configurable Keypad - Metropolitan Style (WIX-xxLV06)
Front Panel
A
D
C
Ambient Light Sensor - Detects the level of ambient light
in the room and adjusts the brightness of the button and
A
dimming LEDs. The ambient light sensor is enabled and
disabled in Blueprint's Lighting and Shade manager.
Dimming Level Indicators - These LEDs can indicate any
of the following:
– The power being applied to the load. The LEDs turn
on from left to right as power is increased and switch
off from right to left as power is decreased.
B
– The power being applied to the load from any scenes
created in Blueprint or the Pro App.
– The status of the keypad during the setup and
provisioning process. See the
Reset Button
Press and release - Reboots the keypad.
C
Press and hold - Press and hold for 10 seconds, then
release to perform a factory reset. A factory reset erases
the keypad's stored address and removes any assigned IP
Addresses.
Buttons - Programmable buttons. See the Low Voltage
Deployment Guide for instructions on how to program.
D
This guide and other lighting information are available on
the Keypad Lighting Documentation Portal in the
Customer Community.
Button LEDs - When configured and bound to a Savant
system, the LED's state is defined by the selection made
E
in the LED Behavior and LED Color fields in the Lighting
and Shades Device Manager.
1 of 5
B
E
Led States
45 Perseverance Way, Hyannis MA 02601.
Savant.com
section.
Savant
| 508.683.2500