Scope of delivery Name Hopper (with lid) Lock screw for Hopper Grind adjustment Grinding degree scale Grinder cover Grind adjustment-lock Display "Program"-bu on Pre-selec on bu on „Single-Shot“ - Grinder 1 Pre-selec on bu on „Single-Shot“ - Grinder 2 10.1 Pre-selec on bu on „Double-Shot“...
K30 TWIN Single Espresso Grinder Inhalt So ware menu ....19 Overview ......2 Accessing and leaving the Scope of delivery ....5 main menu ....... 19 General informa on .... 7 Se ngs ........19 Read opera ng instruc ons and Cleaning ......
Union. Please also note the guidelines and laws of your specifi c country if abroad. For be er clarity, the Double Espresso Grinder K30 TWIN shall be referred to hereina er simply as the “grinder”. Please keep this original instruc on manual safe for later queries.
Page 8
INFORMATION! This signal word warns against possible material damage. This symbol provides you with important informa on concern- ing opera on or handling. Conformity declara on (see chapter “Conformity declara on”): Products marked with this symbol fulfi l all applicable communi- ty provisions of the European Economic Area.
Safety Intended use The grinder is only suitable for grinding whole roast coff ee beans. Do not use the grinder to grind other products or objects. It is intended for commercial use and may only be serviced by trained personnel. It may, however, be operated by other persons in a place where use is supervised.
Page 10
– Do not immerse the grinder or the power cable / power plug in water or any other liquids. – Do not clean the grinder with a water jet. – Do not clean the grinder with compressed air (e.g. with a compressed air blow gun). –...
Page 11
WARNING! Danger for children and persons with reduced physical, sensory and mental abili es (e.g. par ally disabled persons, older persons with limited physical and mental abili es) or a lack of experience and knowledge (e.g. older children). – This grinder may be used by children older than eight years and by persons with reduced physical, sensory or mental disabili es or a lack of experience and knowledge if they are supervised or instructed on the safe use of the grinder and have understood...
Before using Checking grinder and scope of delivery INFORMATION! Risk of damage! The grinder can become damaged if the packaging is opened carelessly with a sharp knife or other pointed object. – Be very careful when opening. 1. Remove the grinder from its packaging. 2.
hopper intake. 9. Seal the hopper by sliding in both sliding valves (24). 10. Place the collec ng tray (16) into the corresponding opening under the outlet (11). Connec ng the poten al equalizer The connec on for poten al equaliza on (18) is located on the back of the grinder (see Fig.
If the portafi lter support does not fi t, contact your supplier (see chapter “Service”). 6. Hold the portafi lter support in posi on and fi x it by turning the screws clockwise for adjus ng the portafi lter support (le and right) un l ght using the Allen key (short, 3 mm).
Adding coff ee beans 1. Remove the lid from the hopper (1). 2. Pour whole roasted coff ee beans into the bean container from above. • The maximum fi lling quan ty should be approx. 1 cm below the edge of the bean container. •...
Only reduce the grinding degree during grinding or when you can be sure that there are no coff ee beans in the grinder. 2. Let go of the grind adjustment. Se ng the grinding me • The factory se ng for the grinding me in single-shot mode is 2.0 seconds (approx.
2. To select the double-shot mode, briefl y press the “Double Shot” pre-se- lec on bu on (10.1) for the le grinder and the pre-selec on bu on (10.2) for the right grinder. 3. To select the barista mode, briefl y press both pre-selec on bu ons (9.1) and (9.2) for the le grinder and the pre-selec on bu ons (10.1) and (10.2) for the right grinder.
Page 18
Changing espresso bean variant 1. Close the hopper (1) by pushing in the sliding valve (24). 2. Grind the remaining espresso beans un l the grinder runs idle (see chap- ter “Grinding coff ee beans”). 3. Remove the le over espresso beans from the hopper. 4.
4. Press the program bu on (8) to access the submenu. A er approx. 30 seconds, the grinder returns to the operator mode. Se ngs See the following overview of the instruc ons for the K30 TWIN so ware.
Cleaning CAUTION! Risk of injury! When being moved the grinder can fall and cause injury. – Place the grinder on a stable, fl at surface so that it cannot wob- ble. – Ask another person for help if the grinder is too heavy. NOTE! Risk of short-circuit! Water entering the grinder can cause a short-circuit.
3. Clean the installa on surface and the underside of the grinder with a damp cloth and dry the surfaces. 4. The surfaces must be dry and free of oil and grease. 5. Place the grinder back onto the cleaned surface. Cleaning the casing 1.
Cleaning the grinder • The manufacturer recommends using GRINDZ grinder cleaner. For more informa on about GRINDZ , visit www.mahlkoenig. • The grinder should be cleaned every 2–5 days. 1. Close the sliding valve (24) by sliding it into the slot below the bean container and grind the remaining espresso beans in the grinder un l the grinder runs idle.
Troubleshoo ng Fault Cause Remedy The grinder is • The outlet is Set the grinding degree humming but not clogged. se ng to “10” and start the grinding. grinding process. The grinder will grind itself clear. Then set the grinding degree se ng to the desired grinding degree during opera on.
Page 26
Fault Cause Remedy • A foreign object is Clean the grinding gear as de- in the grinder. scribed in the chapter “Clean- ing” and remove the foreign object at the same me. If the foreign object cannot be removed, contact your suppli- er using the address indicated “...
Page 27
Fault Cause Remedy • Motor blocked Press the Prog bu on. An- other grinder may con nue • Foreign objects/ to be used beans jammed in the grinder mech- Set the grinding degree of anism the aff ected •...
Page 28
Fault Cause Remedy “VENTILATOR • A foreign object Contact your supplier using is blocking the the address indicated in the BLOCKED” ven lator chapter “Service”. appears on the display • Connector on the processor circuit board not plugged • Ven lator is faulty “VENTILATOR •...
Page 29
Fault Cause Remedy • The installed Contact your supplier using grinder outlet is the address indicated in the damaged. chapter “Service”. • The fl apper is Contact your supplier using faulty. the address indicated in the chapter “Service”. The grinder is •...
Disposal Disposing of the packaging Dispose of the packaging by correctly sor ng the recyclable ma- terials. Dispose of card and cardboard as waste paper, and fi lm as recyclable materials. Disposing of the grinder Old appliances may not be thrown into the commercial/domes c waste! If you can no longer use your grinder, you are legally obliged as a user to dispose of old appliances separately from commercial/do-...
Need help?
Do you have a question about the K30 TWIN and is the answer not in the manual?
Questions and answers