Table of Contents
Advertisement
Service Manual
The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user
status, but do not change the temperature, press "Turbo" button directly for confirmation.
Note: In the above presetting or enquiry procedure, if continuously within10s, there is no button pressed, the sleep
there is no button pressed, the sleep curve setting status will be automatically quit and resume to display the original displaying.
In the presetting or enquiry procedure, press "ON/OFF" button, "Mode" button, "Timer"button or "Sleep" button, the sleep
curve setting or enquiry status will quit similarly.
10
TEMP:
Press this button, could select displaying the indoor setting temperature or indoor ambient temperature.When the indoor unit firstly
power on it will display the setting temperature,if the temperature's displaying status is changed from other status to"
ambient temperature, 5s later or within 5s, it receives other remote control signal that will return to display the setting temperature.
if the users haven't set up the temperature displaying status,that will display the setting temperature.
QUIET:
11
Press this button, the Quiet status is under the Auto Quiet mode (display
singal) and Quiet OFF (there is no signal of "
Note: the Quiet function cannot be set up in Fan and Dry mode;Under the Quiet mode (Display "
not available.
12
CLOCK :
Press CLOCK button, blinking
Holding down either button above 2 seconds increases or decreases the time by 1 minute every 0.5
every 0.5 second. During blinking after setting, press CLOCK button
displayed.
13
T-ON / T-OFF:
Press T-ON button to initiate the auto-ON timer. To cancel the auto-timer program, simply press this button again.
After press of this button,
+ or - butt on to adjust the time value.Every press of either
rapidly changes the time setting by 1 minute and then
Press T-OFF button to initiate the auto-off timer. To cancel the auto-timer program, simply press the button again.TIMER OFF setting
is the same as TIMER ON.
TURBO:
14
Press this button to activate / deactivate the Turbo function which enables the unit to reach the preset temperature in the shortest time.
In COOL mode, the unit will blow strong
high fan speed.
15
LIGHT:
Press LIGHT button to turn on the display's light and press this button again to turn off the display 's light. If the light is turned on
is displayed. If the light is turned off,
WiFi:
16
P
e r
s
s
"
W
i
" i F
b
t u
o t
icon will be displayed on remote controller; Under status of unit off, press "MODE" and "
module will restore to factory default setting.
This function is only available for some models.
Combination of "+" and "-" buttons: About lock
17
" and "- " buttons simultaneously to lock or unlock the keypad. If the remote controller is
Press " +
In this case, pressing any button,
18
Combination of "MODE " and "-" buttons :
"
At unit OFF, press
MODE
19
Combination of " TEMP " and "CLOCK" buttons : About Energy-saving Function
"
"
Press
TEMP
and
Nixie tube on the remote controller displays
Technical Information
. Within 5 seconds,pressing + or - button adjusts the present time.
disappears and "ON "blinks .0
cooling air at super high fan speed. In HEAT mode, the unit will blow strong heating air at super
disappears.
n
o t
u t
n r
o
n
r o
u t
n r
o
f f
W
blinks three times.
About switch between Fahrenheit and centigrade
"
" - "
and
buttons simultaneously to switch between
"
"
CLOCK
simultaneously in COOL mode to start energy-saving function.
"
"
SE
"
"
" displayed), after powered on, the Quiet OFF is defaulted.
again to confirm the setting,and then
0:00 is displayed for ON time setting.Within
button changes the time
10 minutes.Within 5 Seconds after setting,press TIMER
i
i F
u f
n
t c
o i
. n
W
h
e
n
W
i
i F
. Repeat the operation to quit the function.
individuation sleep setting
signal)
and "Auto"
and Quiet mode (display "
" signal),
second and then by 10 minutes
setting by 1minute. Holding down either button
u f
n
t c
o i
n
s i
u t
n r
e
d
o
, n
h t
WiFi
" buttons simultaneously for 1s, WiFi
locked,
and
.
curve setting within10s,
",displays the
"
the fan speed is
will be constantly
5 seconds,press
ON button to confirm.
WiFi
e
"
"
is displayed.
15
Hide quick links:
Advertisement
Table of Contents
