Brc1H Controller; Commissioning; Checklist Before Commissioning - Daikin VAM-J8 Installation And Operation Manual

6
FRESH UP
11
12
13
10
TEST
1 Operation lamp
This red pilot lamp lights up while the unit is in operation.
2 Operation/Stop button
Press this button once and the unit starts to operate. Press this
button again and the unit stops.
3 Air flow rate changeover button
Use this button to change the air flow to " " Low, "
FRESH UP" Low Fresh-up, or "
mode.
When this indication does NOT show, the volume of outdoor air
supplied into the room and that of the room air exhausted
outdoors is equal.
For "FRESH UP" operation
▪ If the Fresh-up setting is set to "Fresh up air supply": The
volume of outdoor air supplied into the room is larger than that
of room air exhausted outdoors. This prevents odours and
moisture from kitchens and toilets from flowing into the room.
This is the factory setting.
▪ If the Fresh-up setting is set to "Fresh up air exhaust": The
volume of room air exhausted outdoors is larger than that of
outdoor air supplied into the room. This prevents hospital
odours and airborne micro-organisms from flowing out of the
room into the corridors.
To change this setting, see List of settings in the installer and
user reference guide.
4 Ventilation mode changeover button:
A
(
(
" " Automatic mode
The unit's temperature sensor automatically changes the
operation mode of the unit to Bypass mode or Heat Reclaim
Ventilation mode.
" " Heat Reclaim Ventilation mode
VAM350~2000J8VEB
Heat reclaim ventilation unit
4P664011-1 – 2021.08
1 2
8
4
3
9
" High, "
FRESH UP" High Fresh-up
In this mode, the outdoor air passes through the heat exchange
element to effect Heat Reclaim Ventilation.
" " Bypass mode
In this mode, the outdoor air does NOT pass through the heat
exchange element, but bypasses it to effect Bypass ventilation.
5 Indication of operation control method:
When operation of the heat reclaim ventilation units is linked to
the air conditioners, this indication may be displayed. While this
indication is displayed, the heat reclaim ventilation units
CANNOT be turned on or off with the controller of the heat
reclaim ventilation units.
6 Indication of operation standby:
This icon indicates that the unit is precooling/preheating. The
unit's start-up is delayed until precooling/preheating is finished.
Precooling/preheating means that the heat reclaim ventilation
units are NOT started while linked air conditioners are starting
up, for example, before office hours.
During this period, the cooling or heating load is reduced to
bring the room temperature to the set temperature in a short
time.
7 Indication of central control:
When a controller for air conditioners or devices for central
control are connected to the heat reclaim ventilation units, this
icon may be displayed.
While this indication is displayed, you may NOT be able to turn
the heat reclaim ventilation units on or off, or use the timer
function with the controller of the heat reclaim ventilation unit.
8 Indication of air filter cleaning
When the display shows "
9 Filter signal reset button
10 Inspection button
Use this button ONLY when servicing the unit.
11 Schedule timer button:
This button enables or disables the schedule timer.
12 Time adjust button:
13 Programming button: /
To set the timer
1 Press the schedule timer button.
2 Press the time adjust button to set the time.
3 Press the programming button to save the setting.
13.4.3

BRC1H controller

INFORMATION
Please refer to the Installer and user reference guide of the
BRC1H user interface.
14

Commissioning

14.1

Checklist before commissioning

After the installation of the unit, first check the items listed below.
Once all checks are fulfilled, the unit MUST be closed. Power-up the
unit after it is closed.
You read the complete installation and operation
instructions, as described in the installer and user
reference guide.
14 Commissioning
", clean the air filter.
/
Installation and operation manual
25